KeylessOption 3-Button Key Fob Remote Control Replacement

پیژندنه

This manual provides comprehensive instructions for the installation, programming, and maintenance of your KeylessOption 3-Button Key Fob Remote Control Replacement. This product is designed to replace your original factory remote with a reliable and functional alternative. Please read all instructions carefully before proceeding.

د بسته محتويات

ډاډ ترلاسه کړئ چې ټول توکي ستاسو په کڅوړه کې شتون لري:

• KeylessOption 3-Button Remote Control(s)
• CR2032 Lithium Battery(s) (pre-installed)
• د کیلي حلقوي لوپونه
• Programming Instructions (included with product)

Figure 1: Contents of the KeylessOption Key Fob package. Includes remote controls, pre-installed batteries, and key ring loops.

د وسایطو مطابقت

This key fob is compatible with specific vehicle models and years. Ensure your vehicle is listed below before attempting to program the remote. This remote is a replacement for OEM part numbers LHJ011, 15186200, 15186201, 15132197, 15132198, 10377295, 22730827, 15186203, & 21997127 (FCC ID: LHJ011).

• Cadillac: Escalade (2003-2007)
• شیورلیټ: Avalanche (2003-2007), Silverado (2003-2007), Suburban (2003-2007), Tahoe (2003-2007)
• GMC: Sierra (2003-2007), Yukon (2003-2007)
• Hummer: H2 (2003-2007)

Figure 2: Visual guide to self-programming and compatible vehicle models.

Key Fob Features

Your KeylessOption remote features three distinct buttons for convenient vehicle control:

• د بندولو تڼۍ: د موټرو ټولې دروازې خوندي کوي.
• د خلاصولو تڼۍ: د موټرو ټولې دروازې خلاصوي.
• د ډار تڼۍ: Activates the vehicle's alarm system for emergency situations.

شکل 3: مخکی view of the key fob, highlighting the Lock, Unlock, and Panic buttons.

د پروګرام کولو لارښوونې

This key fob is designed for self-programming. The exact steps may vary slightly by vehicle model and year. Always refer to your vehicle's owner's manual for the most accurate programming procedure. A common procedure for compatible GM vehicles is as follows:

1. Ensure all vehicle doors are closed.
2. د موټر چلوونکي په څوکۍ کې کښېنئ.
3. Insert your vehicle's ignition key into the ignition.
4. لاندې ونیسئ خلاص کړئ د موټر چلوونکي د غاړې دروازې پینل کې تڼۍ.
5. د ساتلو په وخت کې خلاص کړئ button, cycle the ignition key from بند ته ON او بیرته ته بند two times. Do not start the engine.
6. خوشې کړئ خلاص کړئ button. The vehicle's door locks should cycle (lock and unlock) to indicate that the vehicle is now in programming mode.
7. On the new key fob, simultaneously press and hold the لایک او خلاص کړئ buttons for approximately 15 seconds. The vehicle's door locks should cycle again to confirm successful programming of the first remote.
8. If programming additional remotes (including existing ones), immediately repeat step 7 for each additional remote. All remotes must be programmed during the same session.
9. To exit programming mode, turn the ignition key to the ON position, then remove the key. The door locks should cycle one last time.
10. Test all programmed remotes to ensure full functionality.

Important Note for Multiple Fobs: If you are programming more than one key fob, ensure you program all of them during the same session. If you program one and then exit programming mode before programming the others, the previously programmed fobs may become unprogrammed.

د بیټرۍ بدلول

The key fob uses a CR2032 lithium battery. If the remote's range decreases or it stops responding, the battery may need replacement.

1. Locate the small notch on the side of the key fob.
2. Using a small flat-head screwdriver or a coin, carefully pry open the two halves of the key fob at the notch.
3. Remove the old CR2032 battery. Note the orientation (+/-) of the battery.
4. یو نوی CR2032 بیټرۍ دننه کړئ چې مثبت (+) اړخ یې پورته وي.
5. Carefully snap the two halves of the key fob back together until they are securely closed.
6. Test the key fob's functionality.

Figure 4: Back of the key fob, indicating the opening point for battery replacement.

مشخصات

د ستونزو حل کول

• Fob not responding after programming:
  • Ensure all steps of the programming procedure were followed precisely.
  • If programming multiple fobs, ensure all were programmed in the same session. Reprogram all fobs if necessary.
  • Check the battery. Replace if necessary, ensuring correct polarity.
  • د موټر مطابقت تایید کړئ.
• کم شوی حد:
  • بیټرۍ ممکن ټیټه وي. د CR2032 بیټرۍ بدله کړئ.
  • Ensure there are no obstructions or strong radio interference between the fob and the vehicle.
• تڼۍ سختې یا بې ځوابه دي:
  • Check for debris or damage around the buttons.
  • Ensure the fob is properly assembled after battery replacement.

تضمین او ملاتړ

Your KeylessOption key fob comes with a 90-day warranty from the date of purchase. This warranty covers manufacturing defects and ensures quality and peace of mind. If you experience any defects or issues within this period, please contact KeylessOption customer support for assistance or a replacement.

For further support or to inquire about specific programming details for your vehicle, please refer to your vehicle's owner's manual or visit the official KeylessOption webسایټ