CDVI 433MHz Radio Keypad and Receiver User Manual

1. پیژندنه

This manual provides detailed instructions for the installation, operation, and maintenance of the CDVI 433MHz Radio Keypad (Digicode) and its associated SEL2641R433NN 1-Relay 12V Receiver. This system is designed for secure access control applications.

مهرباني وکړئ دا لارښود په دقت سره ولولئ مخکې لدې چې د هر ډول نصب یا عملیاتو هڅه وکړئ ترڅو مناسب فعالیت او خوندیتوب ډاډمن شي.

Figure 1: CDVI 433MHz Radio Keypad and SEL2641R433NN Receiver. The image shows the silver-colored keypad with illuminated blue numbers (0-9, A, B, C) and a transparent plastic receiver unit.

2. د خوندیتوب معلومات

• ډاډ ترلاسه کړئ چې د نصب یا ساتنې دمخه ټول بریښنا قطع شوې ده.
• نصب کول باید یوازې د وړ پرسونل لخوا ترسره شي.
• Do not expose the keypad or receiver to extreme temperatures, moisture, or direct sunlight.
• Use only specified power supply (12V).
• د ماشومانو د لاسرسي څخه لرې وساتئ.

3. ترتیب او نصب کول

3.1. اجزاوو ختمview

دا سیسټم له دوو اصلي برخو څخه جوړ دی:

• Radio Keypad (Digicode): The input device for entering access codes.
• SEL2641R433NN Receiver: The unit that receives signals from the keypad and controls the access mechanism (e.g., door lock).

3.2. د کیپډ نصب کول

1. Choose a suitable mounting location, typically near the access point, ensuring it is protected from direct weather exposure if outdoors.
2. Mark the drilling points using the keypad's mounting plate as a template.
3. سوري وکړئ او مناسب دیوال پلګونه دننه کړئ.
4. د نصب کولو پلیټ دیوال ته خوندي کړئ.
5. Attach the keypad securely to the mounting plate.

۴.۲. د رسیدونکي تار لګول

The SEL2641R433NN receiver requires a 12V power supply and connection to the access control device. Refer to the wiring diagram below for typical connections.

• د بریښنا ننوتل: Connect 12V DC to the designated terminals. Observe polarity.
• د ریلے محصول: The receiver has one relay. Connect the Normally Open (NO) or Normally Closed (NC) contacts to your access control device (e.g., electric strike, magnetic lock) as required.

(Note: A detailed wiring diagram is typically provided with the physical product. Consult it for specific terminal assignments.)

4. عملیاتي لارښوونې

۱. لومړنی پاور اپ

Once the receiver is wired and powered, it will enter a standby mode. The keypad will illuminate when a button is pressed.

4.2. Programming Access Codes

The keypad and receiver must be paired, and access codes programmed. This process typically involves:

1. د پروګرام کولو حالت ته ننوتل: This usually involves a master code or a physical button on the receiver.
2. Adding New Codes: Follow the specific sequence to input new user codes (e.g., Master Code + * + New Code + #).
3. Deleting Codes: Follow the specific sequence to remove existing user codes.
4. د پروګرام کولو حالت څخه وتل: Save changes and exit programming mode.

(Note: Refer to the specific programming instructions provided with your product for exact key sequences and procedures, as these can vary by firmware version.)

۲. د لاسرسي ورکول

To grant access, simply enter a valid programmed code on the keypad. Upon successful code entry, the receiver's relay will activate for a pre-set duration, unlocking the connected device.

5. ساتنه

• پاکول: د کیپډ سطحه د نرم، ډ سره پاکه کړئamp ټوکر د کثافاتو پاکوونکي یا محلول مه کاروئ.
• منظم چکونه: Periodically check all wiring connections for security and integrity, especially for the receiver unit.
• د کوډ مدیریت: په منظمه توګه بیاview and update access codes for security purposes. Delete codes of former users.

6. ستونزه حل کول

7. مشخصات

8. تضمین او ملاتړ

Information regarding product warranty is typically provided with the purchase documentation or can be found on the manufacturer's official webسایټ. مهرباني وکړئ د تضمین ادعاوو لپاره د پیرود ثبوت وساتئ.

For technical support or further assistance, please contact CDVI customer service or your authorized dealer. Contact details can usually be found on the CDVI webسایټ (www.cdvi.com).