NT-0401 Cable Tester User Manual

1. پیژندنه

The Lanberg NT-0401 is a versatile cable tester designed for verifying the integrity of various network and telephone cables. It supports RJ-45, RJ-12, and RJ-11 connectors, and is compatible with UTP, FTP, and SFTP cable types. Equipped with 9 LED indicators, it provides clear and immediate feedback on cable continuity, open circuits, short circuits, and crossed wires, making it an essential tool for network installation and maintenance.

2. د خوندیتوب معلومات

Please read and understand all safety instructions before operating the device. Failure to do so may result in injury or damage to the device.

• وسیله د لندبل یا خورا تودوخې سره مه ښکاره کوئ.
• د وسیلې د خلاصولو یا بدلولو هڅه مه کوئ. دننه د کارونکي لپاره د خدمت وړ برخې نشته.
• Use only the specified battery type (AAAA) and ensure correct polarity during installation.
• وسیله د قوي بریښنایی مقناطیسي ساحو څخه لرې وساتئ.
• Disconnect the device from cables when not in use.

3. محصول ختم شوview

The NT-0401 cable tester consists of two main components: the Main Unit and the Remote Unit. Both units feature LED indicators for pin-to-pin testing.

Figure 3.1: Lanberg NT-0401 Cable Tester, showing the main unit (left) and the detachable remote unit (right). The main unit features the power switch and multiple ports, while the remote unit has a single RJ45 port.

3.1. اصلي واحد

• RJ-45 بندر: For testing Ethernet cables (Cat5, Cat5e, Cat6, etc.).
• RJ-12/RJ-11 Port: For testing telephone cables.
• BNC Port: For testing coaxial cables.
• LED Indicators (1-8, G): Display the status of each wire pair and ground.
• Power Switch (ON/OFF/S): Controls the device power and test speed. 'S' typically stands for 'Slow' test mode.

3.2. Remote Unit

• RJ-45 بندر: Connects to the far end of the cable being tested.
• LED Indicators (1-8, G): Mirror the main unit's indicators to confirm continuity.

3.2 شکل: تړل view of the Lanberg NT-0401 main unit (left) showing the RJ-45, RJ-12/RJ-11, and BNC ports, along with the LED indicators. The remote unit (right) also displays its corresponding LEDs.

4. ترتیب کول

4.1. د بیټرۍ نصب کول

1. Locate the battery compartment on the back of the Main Unit.
2. د بیټرۍ پوښ خلاص کړئ.
3. Insert one (1) AAAA battery, ensuring correct polarity (+/-) as indicated inside the compartment.
4. د بیټرۍ پوښ په خوندي ډول وتړئ.

4.2. د کیبلونو نښلول

Before testing, ensure the cable is disconnected from any active network devices or power sources.

1. Connect one end of the cable to the appropriate port (RJ-45, RJ-12/RJ-11, or BNC) on the Main Unit.
2. Connect the other end of the cable to the corresponding port on the Remote Unit. For short cables, the remote unit can remain attached to the main unit. For longer, installed cables, detach the remote unit.

5. عملیاتي لارښوونې

5.1. Performing a Cable Test

1. Ensure the cable is properly connected to both the Main and Remote Units.
2. Slide the power switch on the Main Unit to the "ON" position for a normal test speed, or to "S" for a slower test speed (useful for visual inspection of individual wire status).
3. Observe the LED indicators on both the Main and Remote Units.
4. After the test sequence completes, slide the power switch to "OFF" to conserve battery life.

5.2. Interpreting LED Indicators

The LEDs illuminate sequentially, indicating the status of each wire pair (1-8) and the ground (G) connection.

• نورمال اړیکه: LEDs on both the Main and Remote Units illuminate in the same sequence (e.g., 1-2-3-4-5-6-7-8-G).
• Open Circuit (Broken Wire): If a specific LED on the Main Unit illuminates but its corresponding LED on the Remote Unit does not, it indicates an open circuit (broken wire) for that particular pin.
• لنډ تړنه: If two or more LEDs illuminate simultaneously on either unit, or if LEDs fail to illuminate for certain pins while others do, it indicates a short circuit between those wires.
• کراس شوي تارونه: If the sequence of illuminated LEDs on the Remote Unit does not match the sequence on the Main Unit (e.g., Main shows 1-2-3, Remote shows 1-3-2), it indicates crossed wires.
• څراغونه نشته: If no LEDs illuminate, check battery, cable connection, or if the cable is severely damaged.

6. ساتنه

6.1. پاکول

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquid enters the ports or battery compartment.

6.2. ذخیره کول

Store the device in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the battery to prevent leakage.

7. ستونزه حل کول

8. مشخصات

9. تضمین او ملاتړ

For warranty information or technical support, please refer to the documentation included with your purchase or contact Lanberg customer service through their official webسایټ. د تضمین ادعاوو لپاره د پیرود ثبوت وساتئ.

یادونه: د محصول مشخصات او بڼه د مخکینۍ خبرتیا پرته د بدلون تابع دي.