Poolex PC-NAN Heat Pump Instruction Manual

پیژندنه

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Poolex PC-NAN heat pump. The Poolex Nano heat pump is specifically designed for small pools and offers efficient heating with a high Coefficient of Performance (COP) similar to larger heat pumps.

د خوندیتوب معلومات

Please read all safety warnings and instructions carefully before installing and operating this appliance. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• د هر ډول ساتنې یا خدمت ترسره کولو دمخه تل بریښنا قطع کړئ.
• Ensure the electrical system is safe and properly grounded.
• که کومه برخه زیانمنه شوې وي نو واحد مه چلوئ.
• د عملیاتو په جریان کې ماشومان او څاروي له واحد څخه لرې وساتئ.
• نصب کول باید د سیمه ایزو مقرراتو سره سم د وړ مسلکي لخوا ترسره شي.

چمتو کول

The Poolex PC-NAN heat pump is designed for easy installation.

خلاصول او ځای پرځای کول

Carefully remove the heat pump from its packaging. Ensure all components are present. Place the unit on a stable, level surface near your pool, allowing adequate air circulation around the unit.

انځور: مخکینۍ برخه view of the Poolex PC-NAN heat pump, showing the fan grille, control panel, and water inlet/outlet connections.

بریښنایی پیوستون

Connect the heat pump to a conventional electrical socket. The unit comes with a 5-meter power cable equipped with 10mA differential protection for enhanced safety.

Image: Close-up of the 5-meter power cable with integrated differential protection.

د اوبو نښلول

Connect the heat pump to your pool's filtration system using the provided PVC connectors (Ø 32-38). Ensure all connections are secure and leak-free.

Image: A set of PVC connectors and clamps used for connecting the heat pump to the pool's water circulation system.

Image: An outdoor scene showing the Poolex PC-NAN heat pump connected to a small, above-ground wooden pool, demonstrating a typical setup.

عملیاتي لارښوونې

د پیل پیل

Once all connections are secure and the pool's filtration system is running, plug in the heat pump. The unit will begin to heat the pool water.

د حرارت درجه کنټرول

The heat pump is designed to efficiently raise your pool's temperature. Allow several hours for the water to reach the desired temperature, depending on the pool volume and initial water temperature.

Image: A graphic highlighting the 3000W heating capacity and 600W consumption of the Poolex PC-NAN heat pump, indicating its efficiency.

Economic and Quiet Operation

The Poolex PC-NAN is designed to be economical and quiet during operation, making it suitable for residential use.

ساتنه

منظم ساتنه ستاسو د تودوخې پمپ غوره فعالیت او اوږد عمر تضمینوي.

• د تودوخې پمپ شاوخوا ساحه د کثافاتو څخه پاکه وساتئ ترڅو د هوا مناسب جریان ډاډمن شي.
• په دوره یي ډول د واحد بهرنۍ برخه د نرم، ډ سره پاکه کړئamp ټوکر
• Inspect water connections for leaks and tighten if necessary.
• During winterization, follow specific instructions for draining and storing the unit to prevent frost damage.

د ستونزو حل کول

واحد نه پرانیزي

• د بریښنا اتصال چیک کړئ او ډاډ ترلاسه کړئ چې پلګ په بشپړ ډول ساکټ ته داخل شوی.
• Verify that the differential protection on the power cable has not tripped. Reset if necessary.
• Ensure there is power to the electrical outlet.

ناکافي تودوخه

• Check if the pool's filtration system is running, as the heat pump requires water flow to operate.
• Verify that the ambient air temperature is within the operating range for the heat pump.
• Ensure the heat pump is appropriately sized for your pool volume.

غیر معمولي شورونه

• په فین یا د واحد شاوخوا کې د کوم خنډ لپاره وګورئ.
• Ensure the unit is placed on a stable and level surface to minimize vibrations.

مشخصات

تضمین او ملاتړ

For warranty information and technical support, please refer to the official POOLEX webسایټ ته مراجعه وکړئ یا خپل محلي توزیع کونکي سره اړیکه ونیسئ. د پیرود ثبوت په توګه د پیرود رسید وساتئ.

A detailed installation and usage manual is included with your product to provide further guidance.