پیژندنه
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
د خوندیتوب مهمې لارښوونې
- Read these instructions thoroughly before operating the module.
- دا لارښوونې د راتلونکي حوالې لپاره وساتئ.
- په محصول او لارښود کې ټول اخطارونه په پام کې ونیسئ.
- د خوندي عملیاتو لپاره ټولې لارښوونې تعقیب کړئ.
- دا وسیله د اوبو یا رطوبت سره نږدې مه کاروئ.
- یوازې د وچې جامې سره پاک کړئ.
- د وینټیلیشن هیڅ خلاصون مه بندوئ. د جوړونکي لارښوونو سره سم نصب کړئ.
- د تودوخې کومې سرچینې ته نږدې مه نصب کړئ لکه ریډیټرونه، د تودوخې راجسترونه، بخارۍ، یا نور وسایل (په شمول ampلایفیر) چې تودوخه تولیدوي.
- یوازې د جوړونکي لخوا مشخص شوي ضمیمې / لوازم وکاروئ.
- ټول خدمتونه وړ خدماتي پرسونل ته راجع کړئ. خدمت کول اړین دي کله چې وسیله په هر ډول زیانمنه شوې وي.
چمتو کول
د یوروریک نصب کول
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- بندول: Always disconnect power from your Eurorack case before installing or removing any modules.
- پورته کول: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- د بریښنا پیوستون: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- پاور آن: یوځل چې په خوندي ډول نصب او وصل شي، تاسو کولی شئ خپل د یورورک کیس فعال کړئ.
شکل 1: مخکی view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
لومړني اړیکې
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
2 شکل: تړل view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
عملیاتي لارښوونې
اوورview د کنټرولونو
The 1027 module features a clear layout of controls for intuitive sequencing:
- د نرخ نوب: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- آن/آف سویچ: Toggles the sequencer's operation.
- STEP Buttons (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
شکل ۳: زاویه لرونکی view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- ساعت ترتیب کړئ: د کارولو RATE knob او ټیټ/لوړ switch to set the desired tempo. Alternatively, connect an external clock to the CLK IN جیک
- Activate Steps: فشار ورکړئ ګام buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) د حجم ټاکلو لپارهtage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: د د پوستې دروازې will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- پیل / ودرول: د کارولو آن/بند switch to start and stop the sequence.
پرمختللي ځانګړتیاوې
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: د ګام او RESET buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
ساتنه
پاکول
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- د سختې خاورې لپاره، لږ څهampټوکر د اوبو سره ومینځئ. د سختو کیمیاوي موادو یا د کثافاتو پاکوونکو کارولو څخه ډډه وکړئ.
- Do not allow any liquids to enter the module through jacks or openings.
ذخیره کول
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
د ستونزو حل کول
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| ماډل نه فعالیږي. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
مشخصات
| فیچر | تفصیل |
|---|---|
| د ماډل نوم | 1027 |
| د ماډل ډول | تړل شوي ترتیب شوي کنټرول ماډل |
| لړۍ | 2500 لړۍ |
| بڼه | یوروک |
| عرض | 16 HP |
| ژوروالی | Not specified (typical Eurorack depth) |
| د بریښنا مصرف | Not specified (standard Eurorack +12V, -12V) |
| داخلونه | Clock In, External Pulse Width CV |
| محصولات | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| ابعاد (H x W x D) | 43 x 162 x 129 ملي متره (نږدې 1.69 x 6.38 x 5.08 انچه) |
| د توکي وزن | ۰.۴۵ پونډه (تقریبا ۰.۴ کیلوګرامه) |
| د ارتباط ټیکنالوژي | 3.5mm TS jack |
| د بریښنا سرچینه | DC power supply (via Eurorack bus) |
تضمین
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
د تضمین توضیحات: Community. Musictribe. Com.
ملاتړ
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer webسایټ:
- د بهرینګر رسمي Webسایټ
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.