MACHINIST B75 Micro ATX LGA 1155 Motherboard Instruction Manual

1. پیژندنه

This instruction manual provides essential information for the proper installation, configuration, and maintenance of your MACHINIST B75 Micro ATX LGA 1155 Motherboard. Please read this manual thoroughly before proceeding with installation to ensure correct setup and to prevent potential issues. This motherboard is designed to support Intel 2nd and 3rd generation Core i3/i5/i7, Xeon E3/V2 series, Celeron G series, and Pentium G series processors.

2. مشخصات

The following table outlines the key technical specifications of the MACHINIST B75 Micro ATX LGA 1155 Motherboard.

یادونه: مشخصات د مخکینۍ خبرتیا پرته د بدلون تابع دي.

شکل 2.1: پایview of the B75 Pro U5 Motherboard layout.

3. ترتیب او نصب کول

د نصبولو پیل کولو دمخه، ډاډ ترلاسه کړئ چې ستاسو سیسټم بند دی او د دیوال له ساکټ څخه خلاص شوی دی. د مدر بورډ د څنډو له لارې لاس ورکړئ ترڅو د جامد خارج کیدو څخه مخنیوی وشي.

۴.۱. د CPU نصبول

1. په مور بورډ کې د LGA 1155 ساکټ ومومئ.
2. Press the wire buckle by hand and lift it up. Do not remove the black protective cover before installing the CPU.
3. Align the CPU with the socket. The CPU has three bayonets (notches) that correspond to the socket. Carefully place the CPU into the socket, ensuring it sits flush without force.
4. Lower the wire buckle and secure it to lock the CPU in place. The black cover will pop up automatically.

Figure 3.1: Step-by-step guide for CPU installation.

Important CPU Handling Precautions:

• Do not open the CPU top cover.
• Do not touch the CPU pins to contact the core.
• Do not touch the motherboard interface pins.

شکل 3.2: مثالample of normal vs. abnormal CPU socket pins. If abnormal, do not attempt repair; contact support.

۳.۴. د حافظې (RAM) نصبول

The motherboard features two DDR3 Non-ECC memory slots. Ensure your memory modules are compatible with DDR3 1280/1333/1600/1866MHz frequencies.

1. د حافظې سلاټ په دواړو سرونو کې کلپونه خلاص کړئ.
2. Align the notch on the DDR3 memory module with the key in the memory slot.
3. د حافظې ماډل په دواړو سرونو کې په کلکه فشار ورکړئ تر هغه چې کلپونه په خپل ځای کې راشي.

Figure 3.3: Location of DDR3 memory slots.

۲.۴. د ذخیره کولو وسایلو نصبول

The motherboard supports SATA M.2 (NGFF M.2) SSDs and traditional SATA 2.5-inch/3.5-inch drives.

3.3.1. NGFF M.2 SSD Installation

The SATA M.2 (NGFF M.2) interface supports AHCI protocol with transfer rates up to 6Gbps.

1. Locate the NGFF M.2 slot on the motherboard.
2. M.2 SSD په لږ زاویه کې سلاټ ته دننه کړئ.
3. په نرمۍ سره SSD ښکته کړئ او د ورکړل شوي سکرو سره یې خوندي کړئ.

Figure 3.4: SATA M.2 interface and compatible SSD.

۲.۴.۲. د SATA ډرایو نصبول

Connect your SATA hard drives or SSDs to the available SATA ports using SATA data cables. The motherboard includes one SATA 3.0 (6Gb/s) port and three SATA 2.0 (3Gb/s) ports.

Figure 3.5: Location of SATA 3.0 and SATA 2.0 ports.

۲.۵. د توسعې کارت نصبول

The motherboard provides one PCIe 2.0 x16 slot, one PCIe 2.0 x1 slot, and one PCI slot for expansion cards such as graphics cards, sound cards, or network cards.

1. Align the expansion card with the desired slot.
2. Press down firmly until the card is fully seated in the slot and the retention clip (if present) engages.
3. کارت د سکرو سره چیسس ته خوندي کړئ.

شکل 3.6: پایview of PCI and PCIe expansion slots.

3.5. د بریښنا پيوستون

Connect the 24-pin ATX power connector and the 4-pin ATX 12V CPU power connector from your power supply to the corresponding ports on the motherboard.

3.6. د مخکینۍ پینل نښلونکي

Connect the front panel cables (power button, reset button, HDD LED, power LED, USB ports, audio jacks) to their respective headers on the motherboard. Refer to the motherboard diagram for correct pin assignments.

4. د عملیاتو لارښوونې

۴.۱. لومړی بوټ او د BIOS تنظیم

Upon the first power-on after assembly, enter the BIOS setup utility to configure system settings. Typically, this is done by pressing the DEL or F2 key during the boot process. Configure boot order, date/time, and other necessary settings.

4.2. د ډرایور نصب کول

After installing your operating system, install the necessary drivers for the motherboard components (chipset, audio, LAN, USB 3.0). For Windows 10, many drivers may be automatically detected and installed. If manual installation is required, drivers can typically be found on the manufacturer's website or chipset vendor's website (e.g., Intel).

4.3. Integrated Graphics Output

The motherboard supports VGA and HDMI high-definition video output. Ensure your CPU has integrated graphics if you intend to use these ports without a dedicated graphics card. CPUs with an 'F' suffix (e.g., i5-xxxxF) do not have integrated graphics.

Figure 4.1: VGA and HDMI output interfaces.

5. ساتنه

منظم ساتنه ستاسو د مور بورډ او کمپیوټر اجزاو اوږد عمر او باثباته عملیات ډاډمن کولو کې مرسته کوي.

• د دوړو لرې کول: Periodically clean dust from inside your PC case, especially from heatsinks and fans, using compressed air. Ensure the system is powered off and unplugged before cleaning.
• د کیبل مدیریت: Ensure cables are neatly routed to promote good airflow within the case.
• د BIOS تازه معلومات: جوړونکي وګورئ website for BIOS updates. Only update the BIOS if necessary and follow the instructions carefully. Incorrect BIOS updates can damage the motherboard.
• د سافټویر تازه معلومات: Keep your operating system and drivers updated to ensure compatibility and optimal performance.

6. ستونزه حل کول

که تاسو د مور بورډ نصبولو وروسته له ستونزو سره مخ شئ، نو لاندې د ستونزو حل کولو مرحلې په پام کې ونیسئ:

• نه ښودنه/نه بوټ:
  • ډاډ ترلاسه کړئ چې ټول بریښنا کیبلونه (24-pin ATX، 4-pin CPU) په خوندي ډول وصل دي.
  • Reseat the memory modules. Try booting with only one memory stick if you have multiple.
  • Reseat the CPU. Check for any bent pins on the CPU socket (refer to Figure 3.2).
  • If using a dedicated graphics card, ensure it is properly seated and connected to power. Try connecting your monitor to the integrated graphics (VGA/HDMI) if your CPU supports it, to rule out the graphics card as the issue.
  • Clear the CMOS (Complementary Metal-Oxide-Semiconductor) by removing the CMOS battery for a few minutes or using the clear CMOS jumper (refer to motherboard diagram for location).
• Poor Contact Issues: If components like memory, CPU, or graphics card are not making proper contact, gently wipe the metal contacts with an eraser to improve conductivity.
• د موټر چلوونکي ستونزې: If you experience issues with network, audio, or other peripherals, ensure you have installed the correct and latest drivers. For Windows 10, many drivers are automatically installed.
• د سیسټم بې ثباتي/خرابی: Ensure your power supply unit (PSU) provides sufficient and stable power for all components. Check for proper cooling of the CPU and other components.

If problems persist after attempting these steps, it is recommended to seek professional assistance.

7. ملاتړ او تضمین

For technical support, driver downloads, or further assistance, please refer to the official MACHINIST website or contact their customer service channels. While a physical manual is not included with the product, this digital document serves as a comprehensive guide.

د تضمین معلومات: Specific warranty terms and conditions may vary. Please retain your proof of purchase for any warranty claims. For detailed warranty information, consult the product packaging or the official MACHINIST webسایټ

8. محصول ختم شوview ویډیو