LIGHTAILING LED Lighting Kit Instruction Manual

1. پیژندنه

This instruction manual provides detailed guidance for installing and operating your LIGHTAILING LED lighting kit, specifically designed to illuminate the LEGO 75325 The Mandalorian's N-1 Starfighter model. This kit enhances the visual appeal of your LEGO set by adding dynamic lighting effects. Please read all instructions carefully before beginning installation.

Image 1.1: The LEGO 75325 The Mandalorian's N-1 Starfighter model illuminated by the LIGHTAILING LED kit.

2. د خوندیتوب معلومات

• د بریښنا سرچینې حجم ډاډمن کړئtage is less than 5V to prevent damage to the LED components.
• Handle LED wires and components with care. Avoid hard pulling, bending, or shaking, as this can damage the delicate wiring.
• Keep the kit and its components out of reach of small children to prevent choking hazards.
• Do not expose the LED components to water or excessive moisture.
• Always disconnect the power source before performing any maintenance or adjustments.

3. د بسته محتويات

ډاډ ترلاسه کړئ چې لاندې لیست شوي ټول اجزا ستاسو په کڅوړه کې شتون لري:

• 1 x USB LED Light Kit
• 1 x Battery Box (AA batteries not included)
• 1 x د لارښوونې لارښود

Image 3.1: The LIGHTAILING LED kit package and its contents.

۴. د تنظیم او نصبولو لارښود

Follow these steps to install the LED lighting kit into your LEGO 75325 The Mandalorian's N-1 Starfighter model. It is recommended to watch the installation video for visual guidance.

1. Prepare the LEGO Model: Carefully disassemble the necessary sections of your LEGO 75325 model where the lights will be installed. Refer to the included paper instructions or the installation video for specific disassembly points.
2. Install Engine Lights: Place the LED lights into the engine sections of the Starfighter. Ensure the wires are routed discreetly to avoid interference with other LEGO bricks.
3. Install Cockpit and Interior Lights: Position the smaller LED lights within the cockpit and other interior areas as indicated in the guide. Secure the lights and route the wires carefully.
4. د تارونو نښلول: Connect all LED wires to the main USB light kit board. Pay attention to the correct polarity and connection points.
5. Reassemble LEGO Model: Once all lights are in place and wires are connected, carefully reassemble the LEGO model, ensuring no wires are pinched or damaged.
6. بریښنا وصل کړئ: Connect the USB light kit to the battery box or a compatible 5V USB power source.

5. عملیاتي لارښوونې

To operate your LIGHTAILING LED lighting kit:

• د بریښنا سرچینه: Insert three (3) AA batteries (not included) into the battery box, ensuring correct polarity. Alternatively, connect the USB cable directly to a 5V USB power adapter or power bank.
• فعالول: Once connected to a power source, the lights should illuminate automatically. There is no separate on/off switch on the light kit itself; power is controlled by connecting or disconnecting the power source.

6. ساتنه

• پاکول: Use a soft, dry cloth to gently wipe any dust from the LED components and wires. Do not use liquid cleaners.
• ذخیره کول: If storing the LEGO model with the light kit installed, ensure the power source is disconnected. Store in a cool, dry place away from direct sunlight.
• د بیټرۍ بدلول: If using the battery box, replace all three AA batteries simultaneously when the lights dim or stop working.

7. ستونزه حل کول

If you encounter any issues, refer to the table below for common problems and solutions:

8. مشخصات

9. تضمین او ملاتړ

LIGHTAILING is committed to providing quality products and customer satisfaction. For any issues, questions, or support needs regarding your LED lighting kit, please contact our customer service team. Refer to the contact information provided with your product packaging or visit the official LIGHTAILING website for assistance. Please retain your proof of purchase for warranty claims.