Techbee Plug-in Electrical Meter Socket Electricity Usage Monitor

1. محصول ختم شوview

The Techbee Plug-in Electrical Meter Socket is an advanced device designed to help you monitor and manage your electricity consumption. It provides comprehensive data on various electrical parameters, allowing you to identify energy-intensive appliances and optimize your power usage for energy saving and environmental protection.

Figure 1.1: Techbee Plug-in Electrical Meter Socket Electricity Usage Monitor (Model JK-PM04) with its packaging.

کلیدي ځانګړتیاوې:

• Energy-saving and Environmental Protection: Measures power consumption and calculates total energy costs for rational electricity planning.
• Multi-functional Monitoring: Offers 11 display modes including power (Watt), total energy used (kWh), carbon emissions (CO₂), voltage (Volt), current (Amp), frequency (Hz), power factor, cost per kWh, minimum power, and maximum power.
• څو پوړیزه ساتنه: Features warning indicators (screen flash and LED) for preset power, energy cost, or consumption limits. Default overload limit is 3680W, with a recommendation to set it to 1800W for initial use.
• User-friendly Display: Large, easy-to-read display set at a 45-degree angle for optimal visibility.
• Partial Reset Function: Allows deletion of measurement data without affecting original settings (e.g., cost/kWh).
• جوړ شوی بیټرۍ: Retains settings and measured data even when unplugged.

۱. تنظیم او لومړنی کارول

Follow these steps to set up your Techbee Power Meter:

1. بسته بندي کول: Carefully remove the power meter from its packaging.
2. محافظتي فلم: A transparent protective film is present on the screen. You may remove it for clearer visibility or keep it as preferred.
3. پاور آن: Plug the meter directly into a standard electrical wall socket. The display should illuminate. If the screen remains blank or buttons are unresponsive, plugging it into a live socket will resolve the issue as it powers the internal battery and display.
4. Initial Overload Setting: The default overload power limit is 3680W. Before using the energy meter, it is recommended to set the overload power to 1800W for general household appliances. Refer to Section 3.2 for instructions on setting alarm thresholds.
5. وسیله وصل کړئ: Plug the appliance you wish to monitor into the socket on the front of the power meter.

Figure 2.1: The meter features a large display and a built-in battery for convenience.

3. عملیاتي لارښوونې

The Techbee Power Meter features four control buttons: موډ, SET, UP، او ښکته.

3.1. د ښودلو طریقې

فشار ورکړئ موډ button to cycle through the 11 different display modes. Each mode provides specific electrical data:

1. Watt / Total Cost: Displays current power consumption in Watts and accumulated cost.
2. Total kWh Used: Shows the total kilowatt-hours consumed.
3. Carbon Emissions (CO₂): Displays CO₂ emissions based on energy consumption.
4. والیtage / فریکونسی: اوسنی حجم ښیيtage (V) and frequency (Hz) of the power supply.
5. Current / Power Factor: Displays the current (Amp) and power factor.
6. Cost per kWh: د تنظیم کولو اجازه ورکوي او viewing the cost per kilowatt-hour.
7. لږترلږه بریښنا: Shows the lowest recorded power consumption.
8. اعظمي ځواک: Shows the highest recorded power consumption.
9. د اوورلوډ الارم: Displays the set overload power limit.
10. Alarm of kWh: Displays the set kWh alarm limit.
11. Alarm of Cost: Displays the set cost alarm limit.

شکل 3.1: پایview of the 11 monitoring modes available on the device.

3.2. Setting Alarm Thresholds and Cost

To set specific values like cost per kWh or alarm limits:

1. فشار ورکړئ موډ button until you reach the desired setting mode (e.g., "Cost per kWh", "Overload Alarm", "Alarm of kWh", or "Alarm of Cost").
2. فشار ورکړئ SET button. The digit you can adjust will start flashing.
3. د کارولو UP او ښکته د ارزښت د سمون لپاره تڼۍ.
4. مطبوعاتي SET again to move to the next digit or to confirm the setting.
5. Once all digits are set, press موډ د تنظیم کولو حالت څخه وتلو لپاره.

Figure 3.2: The device provides visual alarms (flashing LED and screen indicators) when set thresholds are exceeded.

3.3. Resetting Data

The meter allows for partial data reset, which means you can clear accumulated measurement data (like total kWh or total cost) without losing your custom settings (like cost per kWh or alarm thresholds). To reset measurement data, press and hold the ښکته button for approximately 5 seconds until the relevant data clears.

3.4. Monitoring Appliance Consumption

The meter can precisely detect power usage down to 0.5W, allowing you to identify even the tiniest standby power consumption from your devices. This helps in tracking and reducing unnecessary electricity usage across various household appliances.

Figure 3.3: The power meter can be used to track consumption of various household appliances.

4. ساتنه

To ensure the longevity and accurate performance of your Techbee Power Meter, follow these maintenance guidelines:

• پاکول: وسیله د نرم، وچ ټوکر سره پاک کړئ. د کثافاتو پاکوونکي یا محلولونه مه کاروئ، ځکه چې دوی ممکن نندارې ته زیان ورسوي یا casing.
• ذخیره کول: میټر په یخ او وچ ځای کې د مستقیم لمر وړانګو او سختې تودوخې څخه لرې وساتئ.
• بیټرۍ: The meter includes a built-in Lithium Metal battery. This battery is not user-replaceable and is designed to retain settings and data when the device is unplugged.
• د رطوبت څخه ډډه وکړئ: Do not expose the device to water or high humidity. It is designed for indoor use only.

5. ستونزه حل کول

If you encounter any issues with your Techbee Power Meter, refer to the following common problems and solutions:

6. مشخصات

7. تضمین او ملاتړ

Techbee stands behind the quality of its products. This product comes with a 1 کلن تضمین د پیرود نیټې څخه.

For any questions, technical assistance, or warranty claims, please contact Techbee customer service. We offer lifetime customer service to ensure your satisfaction with our products.

You can find more information and support resources by visiting the official Techbee store: Techbee Store on Amazon.