GODIYMODULES Industrial USB to RS485 Converter User Manual

1. پیژندنه

This manual provides detailed instructions for the installation, operation, and maintenance of the GODIYMODULES Industrial USB to RS485 Converter. This device facilitates communication between a USB-enabled computer and RS485 devices, commonly used in industrial automation, data acquisition, and other serial communication applications. Please read this manual thoroughly before using the product to ensure proper functionality and safety.

Figure 1: GODIYMODULES Industrial USB to RS485 Converter

2. ځانګړتیاوې

• Supports STC MCU download.
• Adjustable baud rate: 300 to 115200 BPS.
• Includes software for serial port setup and power supply configuration.
• Provides 5V, 200mA current to external devices.
• Signal indication: Red LED for data receiving (RXD).
• Signal indication: Green LED for data transmitting (TXD).

Figure 2: Converter with LED RXD, LED TXD, GND, D-/B-, D+/A+, and 5V labels

3. مشخصات

4. ترتیب او نصب کول

Follow these steps to set up your Industrial USB to RS485 Converter:

1. د ډرایور نصب کول: Before connecting the converter, install the necessary USB serial port drivers on your computer. These drivers are typically provided on a mini-CD or available for download from the manufacturer's webسایټ
2. کمپیوټر سره وصل کړئ: Plug the USB end of the converter into an available USB port on your computer. The operating system should detect the new hardware and assign a COM port number.
3. Identify COM Port: Verify the assigned COM port number through your computer's Device Manager (e.g., "Ports (COM & LPT)").
4. Wiring the RS485 Side: Connect your RS485 device to the terminal block of the converter. Ensure correct polarity for D+/A+ and D-/B-. Refer to the connection diagrams below for common configurations.

4.1 د پیوستون ډایگرامونه

Figure 3: Point-to-Point / 2-line Half-Duplex Connection (PC1 to single RS485 device)

• Connect the converter's D+/A+ terminal to the RS485 device's ۴۲+ ترمینل
• Connect the converter's D-/B- terminal to the RS485 device's 485- ترمینل
• د GND او 5V terminals are optional for power supply to external devices if needed.

Figure 4: Point-to-Multipoint / 2-line Half-Duplex Connection (PC1 to multiple RS485 devices)

• Connect the converter's D+/A+ ترمینل ته ۴۲+ bus line.
• Connect the converter's D-/B- ترمینل ته 485- bus line.
• All RS485 devices should be connected in parallel to the same ۴۲+ او 485- bus lines.
• Ensure proper termination resistors are used on the bus if required by your RS485 network.

Figure 5: LX08H to LX08H Half-Duplex Communication

• نښلول D+/A+ of the first converter (PC1) to D+/A+ of the second converter (PC2).
• نښلول D-/B- of the first converter (PC1) to D-/B- of the second converter (PC2).
• This configuration allows two computers to communicate via RS485 using two converters.

5. عملیات

Once the converter is physically connected and drivers are installed, you can begin serial communication.

1. د سافټویر ترتیب: Use a serial communication program (e.g., PuTTY, RealTerm, or custom software) to configure the COM port settings. Ensure the baud rate, data bits, parity, and stop bits match those of your RS485 device.
2. د معلوماتو لیږد: Send and receive data through the configured COM port. The converter will automatically handle the conversion between USB and RS485 signals.
3. د LED شاخصونه:
   • د Red LED (RXD) will flash when the converter is receiving data from the RS485 bus.
   • د Green LED (TXD) will flash when the converter is transmitting data to the RS485 bus.
4. د بهرنۍ بریښنا رسول: If your external RS485 device requires power, you can utilize the 5V او GND terminals on the converter, which provide up to 200mA. Ensure your device's power requirements do not exceed this limit.

6. ساتنه

The GODIYMODULES Industrial USB to RS485 Converter is designed for durability and requires minimal maintenance.

• پاکول: وسیله پاکه او له دوړو څخه پاکه وساتئ. د پاکولو لپاره نرم او وچ ټوکر وکاروئ. د مایع پاکوونکو څخه ډډه وکړئ.
• ذخیره کول: Store the converter in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
• سمبالول: Handle the device with care to prevent physical damage to the USB connector or terminal block.

7. ستونزه حل کول

8. تضمین او ملاتړ

For warranty information and technical support, please refer to the documentation provided with your purchase or contact GODIYMODULES customer service through their official webسایټ