Valkyrie A360 ARGB All-in-One CPU Liquid Cooler User Manual

1. پیژندنه

This manual provides detailed instructions for the installation, operation, and maintenance of your Valkyrie A360 ARGB All-in-One (AIO) CPU Liquid Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. Keep this manual for future reference.

2. د خوندیتوب معلومات

• ډاډ ترلاسه کړئ چې ستاسو د کمپیوټر سیسټم د نصبولو دمخه د دیوال له سایټ څخه بند او خلاص شوی دی.
• د زیان څخه د مخنیوي لپاره اجزا په احتیاط سره سمبال کړئ. د سړې تختې سطحې ته په مستقیم ډول د لمس کولو څخه ډډه وکړئ.
• Do not open the liquid cooler's pump or radiator; it is a sealed unit. Tampایرینګ به تضمین باطل کړي.
• Keep the product away from extreme temperatures, humidity, and direct sunlight.
• Use only the provided mounting hardware to prevent damage to your CPU or motherboard.

3. د بسته محتويات

ډاډ ترلاسه کړئ چې لاندې لیست شوي ټول اجزا ستاسو په کڅوړه کې شتون لري:

• Valkyrie A360 ARGB AIO Liquid Cooler (Radiator, Pump/CPU Block, Tubing)
• د 3 x 120mm ARGB فین
• Intel Mounting Bracket Kit (LGA 1700, 1200, 115X, 2066, 2011)
• AMD Mounting Bracket Kit (AM5, AM4)
• Fan Screws and Radiator Mounting Screws
• حرارتي پیسټ (مخکې له مخکې کارول شوی یا په ټیوب کې)
• ARGB Controller/Cables (if included)
• د کارن لارښود

Image: The Valkyrie A360 ARGB AIO Liquid Cooler showing the radiator, three ARGB fans, and the pump/CPU block unit.

4. ترتیب او نصب کول

4.1. تیاری

• خپل کمپیوټر بند کړئ او ټول کیبلونه پرې کړئ.
• د مور بورډ او CPU ساحې ته د لاسرسي لپاره د خپل کمپیوټر قضیه پرانیزئ.
• که چیرې موجوده کولر بدل کړئ، نو په احتیاط سره یې لرې کړئ او د CPU سطحې څخه هر ډول زاړه حرارتي پیسټ د ایزوپروپیل الکول په کارولو سره پاک کړئ.

۳.۳. د ریډیټر او فین نصب کول

1. Attach the three 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is appropriate for your case (typically exhausting air out or pulling air in).
2. Mount the assembled radiator and fans to an available 360mm mounting location in your PC case (e.g., top, front). Use the shorter radiator mounting screws.

Image: The radiator with three white fans attached, ready for case installation.

۳. د CPU بلاک نصب کول

1. For Intel Sockets: Install the appropriate Intel backplate behind the motherboard. Attach the Intel mounting standoffs to the motherboard.
2. For AMD Sockets: Remove the stock AMD retention brackets from the motherboard, but keep the original backplate. Attach the AMD mounting standoffs to the motherboard.
3. If thermal paste is not pre-applied to the cold plate, apply a small pea-sized amount to the center of your CPU's Integrated Heat Spreader (IHS).
4. Carefully place the CPU block onto the CPU, aligning the mounting holes with the standoffs.
5. Secure the CPU block with the thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

انځور: نږدې انځور view of the Valkyrie A360 CPU block installed on a motherboard, illuminated with blue ARGB lighting.

4.4. کیبل پیوستون

1. Connect the pump's 3-pin or 4-pin power cable to the motherboard header labeled "AIO_PUMP," "CPU_OPT," or "SYS_FAN" (consult your motherboard manual for the recommended header).
2. Connect the ARGB cables from the fans and pump to the included ARGB controller or directly to a 5V 3-pin ARGB header on your motherboard. Ensure correct pin alignment to avoid damage.
3. Connect the fan power cables to available fan headers on your motherboard or to a fan hub/controller.

Image: The Valkyrie A360 AIO cooler fully installed within a white PC case, showcasing the blue ARGB lighting on the fans and CPU block.

5. عملیاتي لارښوونې

۳. لومړنی بریښنا فعالول

After completing the installation, close your PC case, reconnect all external cables, and power on your computer. Observe the cooler for any unusual noises or leaks. Check your system's BIOS/UEFI for CPU temperature readings to confirm proper operation.

۵.۲. د ARGB رڼا کنټرول

If connected to a motherboard's 5V 3-pin ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync). If using the included ARGB controller, refer to its specific instructions for mode and color selection.

Image: The Valkyrie A360 AIO cooler installed in a white PC case, displaying vibrant rainbow ARGB lighting effects on the fans and CPU block.

6. ساتنه

• د دوړو پاکول: د ریډیټر پنکونه او د فین تیغونه په دوره یي ډول پاک کړئ ترڅو د دوړو د راټولیدو مخه ونیول شي، کوم چې کولی شي د هوا جریان او د یخولو فعالیت خنډ کړي. د فشار شوي هوا یا نرم برش څخه کار واخلئ.
• بصری معاینه: Regularly check the tubing and connections for any signs of leaks or damage.
• No Coolant Refill: The Valkyrie A360 is a sealed AIO unit and does not require coolant refills. Opening the unit will void the warranty.

7. ستونزه حل کول

8. مشخصات

9. تضمین او ملاتړ

Valkyrie products are backed by a limited warranty against defects in materials and workmanship. The specific warranty period may vary by region. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please visit the official Valkyrie webسایټ یا د دوی د پیرودونکو خدماتو څانګې سره اړیکه ونیسئ. د اړیکو معلومات معمولا د محصول په بسته بندۍ یا رسمي کې موندل کیدی شي webسایټ

Note: Opening the sealed AIO unit or using non-approved components may void your warranty.