د فعالیت وسیله W1614 2 ټنه (4,000 پونډه) د ظرفیت فرش جیک کارونکي لارښود

پیژندنه

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack. Designed for heavy-duty lifting tasks, this floor jack is constructed from durable steel and features swivel rear casters for easy positioning. It has a maximum lifting capacity of 4,000 pounds and can reach a maximum height of 15 inches.

Figure 1: Performance Tool W1614 2 Ton Floor Jack.

د خوندیتوب معلومات

خبرداری: دا محصول کولی شي تاسو ته د لیډ په شمول کیمیاوي توکو سره مخ کړي ، کوم چې د کالیفورنیا ایالت ته پیژندل شوی ترڅو د سرطان او زیږون نیمګړتیاو یا نورو تولیدي زیان لامل شي. د نورو معلوماتو لپاره لاړ شئ www.P65Warnings.ca.gov.

Always read and understand all instructions and warnings before using this floor jack. Failure to follow these instructions may result in serious injury or property damage.

• په سخت، هموار سطحه کې وکاروئ: Always operate the jack on a hard, level surface capable of supporting the load.
• د جیک سټینډونو څخه کار واخلئ: This floor jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by a floor jack.
• له ټاکل شوي ظرفیت څخه زیات مه کوئ: Never exceed the 4,000 lbs. (2 Ton) rated capacity of this jack.
• Center Load on Saddle: Ensure the load is centered on the jack saddle to prevent slipping.
• Chock Wheels: Always chock the wheels that are not being lifted.
• روښانه وساتئ: Keep hands, feet, and other body parts clear of moving parts and pinch points.
• د کارولو دمخه معاینه وکړئ: د هرې کارونې دمخه، جیک د کوم زیان، لیک یا خلاصو برخو لپاره معاینه کړئ. که زیانمن شوی وي نو مه یې کاروئ.
• د اوورلوډ محافظت: This jack is equipped with an overload protection bypass valve for safety. Do not attempt to bypass or modify this feature.

تنظیم او ابتدايي چمتووالی

Before first use, or if the jack has been stored for an extended period, it is important to bleed any air from the hydraulic system to ensure proper operation. Air in the system can cause the jack to lift unevenly or not lift at all.

د هیدرولیک سیسټم وینه بهیدنه:

1. Locate the release valve. This is typically a screw or knob that controls the lowering function.
2. لاسي د لاسي ساکټ ته دننه کړئ.
3. لاستی د ساعت په مخالف لوري وګرځوئ ترڅو د خوشې کولو والو په بشپړه توګه خلاص شي.
4. Pump the handle fully up and down approximately 10-15 times to force any trapped air out of the system.
5. لاستی د ساعت په لور وګرځوئ ترڅو د خوشې کولو والو بند کړئ.
6. Test the jack by pumping the handle to raise the saddle. It should raise smoothly and evenly. If not, repeat the bleeding process.

شکل ۳: زاویه لرونکی view of the floor jack, showing the handle socket and general structure.

عملیاتي لارښوونې

د موټر پورته کول:

1. Park the vehicle on a hard, level surface. Engage the parking brake and chock the wheels that will remain on the ground.
2. Locate the vehicle's manufacturer-recommended lifting points. Refer to your vehicle's owner's manual.
3. Position the floor jack so that the saddle is directly under the lifting point. Ensure the load is centered on the saddle.
4. Close the release valve by turning the handle clockwise until it is firmly closed. Do not overtighten.
5. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to place jack stands.
6. سمدلاسه د موټر د ټاکل شویو ملاتړ ځایونو لاندې مناسب درجه بندي شوي جیک سټینډونه ځای په ځای کړئ.
7. Slowly open the release valve by turning the handle counter-clockwise to lower the vehicle onto the jack stands. Once the vehicle is securely resting on the jack stands, remove the floor jack.

د موټر ښکته کول:

1. Ensure the area around the vehicle is clear of obstructions and personnel.
2. Position the floor jack saddle directly under the vehicle's lifting point, adjacent to the jack stands.
3. Pump the jack handle a few times to slightly raise the vehicle off the jack stands.
4. د موټر لاندې څخه د جیک سټینډونه په احتیاط سره لرې کړئ.
5. Slowly turn the jack handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. کله چې موټر په بشپړه توګه ښکته شي، د فرش جیک لرې کړئ.

Figure 3: Diagram showing key dimensions and lift range of the floor jack.

ساتنه

• غوړول: په دوره یي ډول ټولې خوځنده برخې د سپک ماشین تیلو سره غوړ کړئ.
• هیدرولیک مایع: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other types of oil.
• پاکول: جیک پاک وساتئ او له خاورې، غوړ او کثافاتو څخه پاک وساتئ.
• ذخیره کول: Store the jack in a dry, clean place with the ram fully retracted to prevent rust and extend seal life.
• معاینه: Regularly inspect for any signs of wear, damage, or leaks. If any issues are found, do not use the jack and have it serviced by qualified personnel.

د ستونزو حل کول

مشخصات

تضمین او ملاتړ

For specific warranty information, please refer to the documentation included with your purchase or contact Performance Tool customer service. Keep your purchase receipt for warranty claims.

د کارونکي رسمي لارښود (PDF) د ډاونلوډ لپاره شتون لري: د کارونکي لارښود (PDF) ډاونلوډ کړئ

For technical support or inquiries, please visit the official Performance Tool webسایټ یا د دوی د پیرودونکي خدماتو څانګې سره اړیکه ونیسئ.