پیژندنه
This manual provides essential instructions for the safe operation, maintenance, and storage of your Performance Tool W1611 2.25 Ton (4,500 lbs) Capacity Trolley Jack. Before using the jack, it is crucial to read and understand all instructions and safety warnings to prevent injury or property damage. Keep this manual for future reference.
Image: The Performance Tool W1611 2.25 Ton Trolley Jack, a yellow hydraulic jack with a long handle.
د خوندیتوب مهم معلومات
WARNING: Failure to heed these warnings may result in personal injury or property damage.
- ټولې لارښوونې ولولئ: Understand the operation and limitations of the jack, as well as the hazards involved.
- په سخت، هموار سطحه کې وکاروئ: Always use the jack on a hard, level surface capable of supporting the load. Avoid soft ground or uneven surfaces.
- له ټاکل شوي ظرفیت څخه زیات مه کوئ: The W1611 jack has a maximum capacity of 2.25 tons (4,500 lbs). Do not attempt to lift loads heavier than this rating.
- د جیک سټینډونو څخه کار واخلئ: This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a jack.
- بار په مرکز کې واچوئ: ډاډ ترلاسه کړئ چې بار د جیک سیډل په مرکز کې دی. د مرکز څخه بهر بارونه کولی شي بې ثباتي رامینځته کړي.
- روښانه وساتئ: لاسونه، پښې او د بدن نور برخې د حرکت کوونکو برخو او د بار لاندې ساحې څخه پاک وساتئ.
- د هر استعمال څخه مخکې معاینه کړئ: Check the jack for any damage, leaks, or loose parts before each use. Do not use if damaged.
- ورو ورو ښکته کول: تل بار ورو او په کنټرول شوي ډول کم کړئ.
- وړاندیز 65 خبرداری: دا محصول ممکن د کالیفورنیا ایالت ته پیژندل شوي کیمیاوي توکي ولري چې د سرطان او زیږون نیمګړتیاو یا نورو زیږون زیان لامل کیږي. له مینځلو وروسته لاسونه ومینځئ.
د بسته محتويات
د خلاصولو پر مهال ډاډ ترلاسه کړئ چې ټولې برخې شتون لري:
- 1 Performance Tool W1611 2.25 Ton Trolley Jack
- 1 Operating Handle
- 1 Blow-molded plastic storage case
مشخصات
| فیچر | مشخصات |
|---|---|
| ماډل | W1611 |
| د بار کولو ظرفیت | ۳.۵ ټنه (۷۰۰۰ پونډه) |
| د پورته کولو لږترلږه لوړوالی | 5-1/4 انچه |
| د پورته کولو اعظمي لوړوالی | 15 انچه |
| د محصول ابعاد (L x W x H) | 23.2 x 10.3 x 6.8 انچه |
| د توکي وزن | Approximately 27 lbs (including case) |
| زینه | Steel lifting saddle with 360-degree swivel |
| څرخ | Heavy-duty steel front wheels, ball-bearing swivel rear wheels |
انځور: نږدې انځور view highlighting the steel lifting saddle and the heavy-duty wheels of the trolley jack.
تنظیم او ابتدايي چمتووالی
1. خلاصول
Carefully remove the trolley jack and its components from the packaging. Inspect for any shipping damage. If any damage is found, do not use the jack and contact customer support.
2. د مجلس اداره کول
Insert the operating handle into the handle socket on the jack. Ensure it is securely seated. Some models may require tightening a set screw.
3. Bleeding the Hydraulic System
Before first use, or if the jack has been stored for an extended period, it is recommended to bleed any air from the hydraulic system to ensure proper operation. This procedure helps distribute fluid evenly through internal components.
- Locate the release valve (typically a screw or knob near the handle socket).
- Turn the release valve counter-clockwise to open it fully.
- Pump the handle vigorously six (6) to ten (10) times. This action will cycle the hydraulic fluid and expel any trapped air.
- Turn the release valve clockwise to close it firmly. The jack is now ready for use.
عملیاتي لارښوونې
۵.۱. د موټر پورته کول
- موټر چمتو کړئ: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground to prevent movement.
- د جیک ځای ونیسئ: Locate the manufacturer-recommended lifting points on your vehicle's frame or chassis. Position the jack so the saddle is directly under the lifting point. Ensure the jack is stable and the load is centered on the saddle.
- موټر پورته کړئ: Close the release valve by turning it clockwise until it is firm. Pump the operating handle up and down to raise the vehicle to the desired height.
- د جیک سټینډونو سره خوندي: Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.
۵.۲. د موټر ښکته کول
- ساحه پاکه کړئ: Ensure all tools, personnel, and obstructions are clear from under and around the vehicle.
- لږ پورته کړئ: که چیرې موټر په جیک سټینډونو کې وي، نو د جیک هینډل څو ځله پمپ کړئ ترڅو موټر د جیک سټینډونو څخه لږ څه پورته شي.
- د جیک سټینډونه لرې کړئ: د موټر لاندې څخه د جیک سټینډونه په احتیاط سره لرې کړئ.
- موټر ښکته کړئ: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Once fully lowered, remove the jack.
Image: The Performance Tool W1611 trolley jack positioned for lifting, demonstrating its extended handle and low profile.
ساتنه
Regular maintenance ensures the longevity and safe operation of your trolley jack.
- پاکول: Keep the jack clean and free of dirt, grease, and debris. Wipe down the exterior with a clean cloth after each use.
- غوړول: Periodically lubricate the pivot points, wheels, and especially the wheel castor bearings with light machine oil to ensure smooth operation and prevent rust.
- هیدرولیک مایع: Check the hydraulic fluid level periodically. If the fluid level is low, consult a qualified service technician for proper refilling with hydraulic jack oil. Do not use brake fluid or other non-specified fluids.
- معاینه: Regularly inspect the jack for any signs of wear, damage, or leaks. Pay close attention to welds, the hydraulic cylinder, and the handle. If any issues are found, discontinue use and have it repaired by a qualified professional.
د ستونزو حل کول
د عامو ستونزو او د هغوی احتمالي حلونو لپاره لاندې جدول ته مراجعه وکړئ.
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| Jack will not lift or lifts slowly | په هیدرولیک سیسټم کې هوا د کم هیدرولیک مایع کچه د خوشې کولو والو په بشپړه توګه تړل شوی نه دی | Bleed the hydraulic system (refer to Setup section) Consult a qualified technician to check/refill fluid Ensure release valve is firmly closed clockwise |
| جیک د بار لاندې ښکته کوي | د خوشې کولو والو په بشپړه توګه تړل شوی نه دی Internal hydraulic leak اوورلوډ | Ensure release valve is firmly closed Discontinue use and consult a qualified technician Ensure load does not exceed 2.25 tons (4,500 lbs) |
| Jack is difficult to pump | په هیدرولیک سیسټم کې هوا په حرکتي برخو کې د غوړولو نشتوالی Damaged pump mechanism | د هیدرولیک سیسټم خونریزي Lubricate pivot points and wheels د یو وړ تخنیکین سره مشوره وکړئ |
ذخیره کول
Proper storage helps maintain the jack's condition and readiness for use.
- د ذخیره کولو دمخه پاک کړئ: Ensure the jack is clean and dry before storing.
- Lower Ram Fully: Always lower the jack's ram completely before storage to relieve pressure on the hydraulic system.
- د ذخیره کولو قضیه وکاروئ: Store the jack in its provided blow-molded plastic case to protect it from dust, moisture, and damage. This also prevents it from rolling around if stored in a vehicle.
- په وچ ځای کې ذخیره کول: Store the jack in a dry, protected area, away from corrosive materials and extreme temperatures.
Image: The Performance Tool W1611 trolley jack alongside its durable black plastic storage case, emphasizing portability and protection.
تضمین او ملاتړ
For warranty information or technical support regarding your Performance Tool W1611 2.25 Ton Trolley Jack, please refer to the documentation included with your purchase or visit the official Performance Tool webسایټ. د پیرودونکو خدماتو لپاره د اړیکو توضیحات معمولا د تولید کونکي په ویب پاڼه کې شتون لري webسایټ یا د محصول بسته بندي.
تاسو کولی شئ لیدنه وکړئ Performance Tool Store on Amazon د نورو محصولاتو معلوماتو او ملاتړ سرچینو لپاره.
