پیژندنه
This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of the Fluke 8808A 5.5-Digit Digital Bench Multimeter. Please read this manual thoroughly before using the instrument.
The Fluke 8808A is a high-performance digital multimeter designed for precision measurements in various electrical and electronic applications. It features a 5.5-digit resolution, dual display, and capabilities for measuring volts, ohms, and amps with high accuracy.
د خوندیتوب معلومات
Always adhere to safety precautions to prevent personal injury and damage to the instrument. Observe all warnings and cautions marked on the instrument and in this manual.
- Do not use the multimeter if it is damaged or operating abnormally.
- Ensure proper input connections for the measurement type.
- Do not exceed the maximum input ratings for any function.
- یوازې مشخص شوي بدیل برخې وکاروئ.
- Refer to the specifications section for detailed input limits.
محصول پای ته ورسیدview
The Fluke 8808A is a versatile bench multimeter with the following key features:
- 5.5-digit resolution dual display
- Basic V dc accuracy of 0.015%
- Dedicated DC leakage current measurement
- 2x4 ohms 4-wire measurement technique
- Six dedicated buttons for fast access to instrument setups
- Hi/Lo limit compare for Pass/Fail testing
Figure 1: Front panel of the Fluke 8808A Digital Bench Multimeter, showing the display, input terminals, and control buttons. The display shows a reading of 1.61572 V DC. Input terminals are labeled for HI, LO, mA, and 10A, with additional SENSE 4WD terminals.
چمتو کول
پیک کول او تفتیش کول
Carefully unpack the multimeter and inspect it for any signs of damage during transit. Report any damage to your dealer or Fluke representative immediately.
د بریښنا پیوستون
The Fluke 8808A operates on 110V/120V AC power. Connect the supplied power cord to the instrument's rear panel power inlet and then to a grounded AC outlet. Ensure the correct voltage setting if applicable (check the rear panel for voltage selector, though typically auto-sensing for 110V/120V models).
ابتدايي بریښنا فعاله ده
- د بریښنا ت buttonۍ فشار کړئ (⑂) located on the front panel.
- The display will illuminate and perform a self-test.
- Allow the instrument to warm up for at least 30 minutes for optimal accuracy.
عملیاتي لارښوونې
د فرنټ پینل کنټرولونه او نښلونکي
Refer to Figure 1 for the layout of the front panel. Key areas include:
- د ننوتلو ترمینلونه: Located on the left, these are used for connecting test leads for voltage, current, and resistance measurements. Includes HI, LO, mA, and 10A terminals.
- Sense Terminals (4-wire): Used for 4-wire resistance measurements to eliminate lead resistance errors.
- ښکاره کول: Shows measurement readings, units, and status indicators.
- د فعالیت تڼۍ: Buttons like DC V, AC V, DC I, AC I, Ω (Ohms), Freq (Frequency) select the primary measurement function.
- Range Buttons: Used to manually select measurement ranges or enable auto-ranging.
- Setup Buttons (S1-S6): Allow saving and recalling up to six instrument configurations for frequently performed measurements.
- Utility Buttons: Include MIN/MAX, REL (Relative), HOLD, RATE/TRIG, PRINT/BAUD, and SHIFT for advanced functions.
بنسټیز اندازه کول
د DC حجم اندازه کولtagای (ډي سي وي)
- سره د سور ازموینې لیډ وصل کړئ HI input terminal and the black test lead to the LO د ننوتو ترمینل.
- فشار ورکړئ ډي سي وي تڼۍ
- د ازموینې لیډونه د سرکټ یا برخې په اوږدو کې وصل کړئ ترڅو اندازه شي.
- د DC والیtagد e لوستل به په نندارتون کې ښکاره شي.
Measuring Resistance (Ω)
- د مقاومت اندازه کولو دمخه ډاډ ترلاسه کړئ چې سرکټ غیر انرژي شوی دی.
- For 2-wire measurement: Connect the red test lead to the HI input terminal and the black test lead to the LO د ننوتو ترمینل.
- For 4-wire measurement (recommended for precision): Connect the HI test lead to the HI input, LO test lead to the LO input, HI sense lead to SENSE HI, and LO sense lead to SENSE LO.
- فشار ورکړئ اومه تڼۍ
- د ازموینې لیډونه د برخې په اوږدو کې وصل کړئ.
- د مقاومت لوستل به په نندارتون کې څرګند شي.
Using Setup Buttons (S1-S6)
The six setup buttons allow for quick recall of frequently used measurement configurations.
- To Save a Setup: Configure the multimeter for the desired measurement function, range, limits, etc. Then, press the SHIFT button followed by one of the S1 ته S6 buttons. The current configuration is saved to that button.
- To Recall a Setup: Simply press the desired S1 ته S6 button. The multimeter will instantly switch to the saved configuration.
ساتنه
پاکول
د وسیلې قضیه د اعلان سره پاکه کړئamp cloth and mild detergent. Do not use abrasives or solvents. Ensure the instrument is powered off and disconnected from all power sources before cleaning.
کیلیبریشن
For optimal performance and accuracy, the Fluke 8808A should be calibrated periodically by qualified personnel using traceable standards. Refer to the service manual for detailed calibration procedures or contact Fluke service centers.
د فیوز بدلول
If the current measurement function fails, the fuse may need replacement. Refer to the service manual for fuse specifications and replacement instructions. Always replace fuses with the exact type and rating specified by the manufacturer.
د ستونزو حل کول
This section provides solutions to common issues. If the problem persists, contact Fluke technical support.
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| هیڅ ښودنه یا ځواک نشته | د برېښنا تار نه دی وصل شوی؛ د برېښنا ساکټ خراب شوی؛ داخلي فیوز چاودېدلی دی. | Check power cord connection; Test power outlet; Check and replace internal fuse (refer to Maintenance). |
| غلط لوستل | Incorrect function selected; Test leads faulty; Calibration required; Environmental factors. | Verify selected function; Check test leads for continuity; Perform calibration; Ensure stable operating environment. |
| اوسنی اندازه کول کار نه کوي | Blown current fuse. | Replace the appropriate current fuse (refer to Maintenance). |
| Setup buttons not saving/recalling | Incorrect procedure for saving/recalling. | Ensure SHIFT is pressed before S1-S6 to save, and only S1-S6 to recall. |
مشخصات
The following are key specifications for the Fluke 8808A Digital Bench Multimeter:
- د ماډل شمیره: 8808A
- قرارداد: 5.5 عددونه
- Basic DC Voltagدقت: 0.015%
- د اندازه کولو دندې: DC Voltage، AC Voltage, DC Current, AC Current, Resistance (2-wire and 4-wire), Frequency, Continuity, Diode Test
- ننوتۍ جلدtage درجه بندي: 1000V CAT I, 600V CAT II, 300V CAT III
- د اوسني اندازه کولو سلسله: Up to 10A (200mA MAX, 10A MAX)
- د مقاومت اندازه کول: 2x4 ohms 4-wire technique
- ښکاره کول: دوه ګونی ننداره
- Primary Power Source: 110V/120V AC
- ابعاد (L x W x H): 11.7 x 8.56 x 3.7 انچه
- وزن: 1 پونډه
- UPC: 095969340137
تضمین او ملاتړ
د تضمین معلومات
Fluke products are warranted to be free from defects in material and workmanship under normal use and service. The warranty period for the Fluke 8808A is typically one year from the date of purchase, but may vary by region. Please refer to the warranty card included with your product or visit the official Fluke webد تضمین د تفصيلي شرایطو او مقرراتو لپاره سایټ.
تخنیکي ملاتړ
For technical assistance, troubleshooting, or service inquiries, please contact Fluke customer support. You can find contact information on the official Fluke webسایټ یا ستاسو د محلي توزیع کونکي له لارې.
رسمي فلوک Webسایټ: www.fluke.com
