1. د خوندیتوب معلومات
د کار کولو دمخه د محصول ځانګړتیاو سره آشنا کیدو لپاره د لارښوونې بشپړ لارښود ولولئ. د محصول په سمه توګه نه چلول کولی شي محصول، شخصي ملکیت ته زیان ورسوي او جدي ټپي کیدو لامل شي. دا یو پیچلی شوقي محصول دی. دا باید په احتیاط او عقل سره چلول شي او ځینې لومړني میخانیکي وړتیا ته اړتیا لري. د دې محصول په خوندي او مسؤلانه ډول نه چلول کولی شي محصول یا نورو ملکیت ته زیان یا زیان ورسوي. دا محصول د ماشومانو لخوا د کارولو لپاره نه دی. د غیر مطابقت لرونکي اجزاو سره مه کاروئ یا دا محصول په هیڅ ډول د هوریزون هوبي، LLC لخوا چمتو شوي لارښوونو څخه بهر بدل کړئ. دا لارښود د خوندیتوب، عملیاتو او ساتنې لپاره لارښوونې لري. دا اړینه ده چې د راټولولو، تنظیم کولو یا کارولو دمخه په لارښود کې ټولې لارښوونې او اخطارونه ولولئ او تعقیب یې کړئ ترڅو په سمه توګه کار وکړئ او د زیان یا جدي ټپي کیدو څخه مخنیوی وکړئ.
2. محصول ختم شوview
The ARRMA ARAC9030 Rear Suspension Arm Set is designed for the Raider ADX10 RC vehicle. These suspension arms are manufactured from a super-durable, high-quality composite material, ensuring long-lasting performance across various terrains.
کلیدي ځانګړتیاوې:
- High-strength moulded 'webbing' for enhanced durability.
- Precision manufactured shock mounting holes for secure fitment.
- Specially designed hinge pin capture screw holes for maximum reliability.
د بسته محتويات:
- 2 x Rear Suspension Arms
Image 1: The ARRMA ARAC9030 Rear Suspension Arm Set, showing two black composite suspension arms with associated parts.
3. نصب او تنظیم کول
This section provides general guidance for installing the ARRMA ARAC9030 Rear Suspension Arm Set. Refer to your specific Raider ADX10 vehicle manual for detailed disassembly and assembly instructions.
اړین اوزار (شامل نه دي):
- Hex wrenches (appropriate sizes for your vehicle)
- د کوچني فیلیپس سر سکریو ډرایور
- د پوزې ستنې (اختیاري)
د نصبولو مرحلې:
- چمتووالی: Ensure your RC vehicle is powered off and the battery is disconnected. Place the vehicle on a stable, clean surface.
- څرخونه لرې کړئ: Carefully remove the rear wheels from the vehicle.
- Disconnect Shocks: Detach the lower end of the rear shock absorbers from the existing suspension arms.
- Remove Hinge Pins: Locate and remove the hinge pins that secure the old suspension arms to the chassis and the hub carriers. Note the orientation of any spacers or washers.
- زړې وسلې لرې کړئ: Once the hinge pins are removed, carefully detach the old rear suspension arms.
- Install New Arms: Position the new ARRMA ARAC9030 suspension arms in place. Ensure correct left and right orientation if applicable.
- Secure Hinge Pins: Reinsert the hinge pins through the new suspension arms, chassis, and hub carriers. Ensure all spacers and washers are correctly reinstalled. Secure the hinge pins using the capture screws.
- Reconnect Shocks: Reattach the lower end of the shock absorbers to the designated mounting holes on the new suspension arms.
- څرخونه بیا نصب کړئ: Mount the rear wheels back onto the vehicle.
- وروستی چک: Gently move the suspension up and down to ensure free movement and proper installation. Check all screws and fasteners for tightness.
۳. عملیاتي ملاحظات
Once installed, the rear suspension arms are an integral part of your RC vehicle's handling and performance. Proper installation ensures optimal suspension travel and durability during operation. Always operate your RC vehicle responsibly and within its intended design limits.
- Avoid extreme impacts that could damage suspension components.
- Regularly inspect suspension arms for signs of wear or damage after each use.
- Ensure all fasteners remain tight to prevent parts from loosening during operation.
5. ساتنه
Regular maintenance of your ARRMA ARAC9030 Rear Suspension Arm Set will extend its lifespan and ensure consistent performance.
- پاکول: After each use, especially in dirty or dusty conditions, clean the suspension arms and surrounding areas to remove debris. A soft brush and compressed air can be effective. Avoid harsh chemicals that may degrade the composite material.
- معاینه: Periodically inspect the suspension arms for cracks, bends, or any signs of stress or fatigue. Pay close attention to the hinge pin areas and shock mounting points.
- د تړلو چک: Ensure all screws and hinge pins associated with the suspension arms are securely fastened. Loose fasteners can lead to premature wear or component failure.
- بدلول: If any damage is observed, replace the suspension arms immediately to prevent further damage to your vehicle or compromised handling. Use genuine ARRMA replacement parts for best results.
6. ستونزه حل کول
This section addresses common issues related to the rear suspension arms.
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| Suspension feels loose or has excessive play. | Loose hinge pins or mounting screws; worn hinge pin holes. | Check and tighten all fasteners. If holes are worn, replace the suspension arms. |
| Vehicle pulls to one side. | Bent or damaged suspension arm; uneven shock absorber settings. | Inspect arms for damage and replace if necessary. Verify shock settings are symmetrical. |
| Suspension arms appear cracked or broken. | د اغیز زیان؛ د موادو ستړیا. | Replace the damaged suspension arm(s) immediately. |
7. مشخصات
| فیچر | تفصیل |
|---|---|
| د محصول نوم | Suspension Arm Set Rear: Raider ADX10 |
| د ماډل شمیره | ARAC9030 |
| برانډ | ARRMA |
| مواد | High-quality Composite |
| مطابقت | Raider ADX10 |
| د محصول ابعاد | 11.38 x 4.13 x 0.38 انچه |
| د توکي وزن | 1.92 اونس |
| د جوړونکي وړاندیز شوی عمر | 14 کاله او پورته |
8. تضمین او ملاتړ
For specific warranty information and technical support regarding your ARRMA ARAC9030 Rear Suspension Arm Set, please refer to the official ARRMA webسایټ ته مراجعه وکړئ یا د دوی د پیرودونکو خدماتو څانګې سره اړیکه ونیسئ. د هر ډول تضمین ادعا لپاره د پیرود ثبوت وساتئ.
جوړونکی: ARRMA
Webسایټ: www.arrma-rc.com
