پیژندنه
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Maxxima M50910 LED Flasher Module. This module is designed to provide 16 selectable flash patterns for 12-volt DC LED lighting applications, enhancing visibility and safety.
د خوندیتوب معلومات
- د ماډل نصبولو یا خدمت کولو دمخه تل بریښنا قطع کړئ.
- ډاډ ترلاسه کړئ چې د تارونو ټولې اړیکې خوندي او په سمه توګه موصل شوي دي ترڅو د لنډ سرکټ مخه ونیول شي.
- This module is designed for 12 Volt DC systems only. Connecting to other voltage sources may cause damage.
- The module has a maximum current capacity of 20 Amps total (10 Amps per channel). Do not exceed this rating.
- Installation should be performed by individuals with basic knowledge of automotive electrical systems.
د بسته محتويات
- Maxxima M50910 LED Flasher Module
- د لارښوونې لارښود (دا سند)
تنظیم او نصب کول
The Maxxima M50910 LED Flasher Module is designed for straightforward installation. Refer to the wiring diagram below for proper connections.
انځور 1: Maxxima M50910 LED Flasher Module showing input, output, and flash pattern wires. The module is black with red, black, and yellow input wires on one side, and two red output wires on the other. Text on the module indicates "Maxxima", "M50910 LED Flasher Module", "12 Volt DC only", and "20 Amp Max".
د تار لګولو لارښوونې:
- د بریښنا ننوتل: سره وصل کړئ red input wire to a 12V DC positive (+) power source. Connect the تور داخل تار to a common ground (-) connection.
- د رڼا محصول: دواړه سره وصل کړئ red output wires to your LED lights. Each output channel can handle up to 10 Amps. A common ground can be used for the lights.
- د فلش نمونې کنټرول: سره وصل کړئ ژیړ تار to a momentary switch. This switch should connect the yellow wire to a 12V positive (+) source when pressed.
- پورته کول: Secure the module using its integrated bracket mounts. Ensure it is placed in a location protected from excessive heat and physical damage. The module is epoxy potted for water resistance.
It is recommended to use LED lights with this module for optimal performance, as incandescent bulbs may not keep up with high-speed flash patterns.
عملیاتي لارښوونې
The M50910 module offers 16 distinct flash patterns. Follow these steps to operate the module:
- څراغونه فعال کړئ: Turn on the power to your connected lights. The module will begin flashing with the last selected pattern.
- د فلش بڼه بدله کړئ: Briefly press and release the momentary switch connected to the yellow wire (approximately 1 second). Each press will cycle to the next available flash pattern.
- Solid On Function: Some patterns may include a "solid on" mode. Cycle through the patterns to find this option if desired.
- Reset Patterns: To reset the module to the first flash pattern, press and hold the momentary switch connected to the yellow wire for 10-15 seconds.
- د حافظې دنده: The module retains the last selected flash pattern even after power is removed.
ساتنه
The Maxxima M50910 LED Flasher Module is designed for durability and requires minimal maintenance.
- پاکول: Keep the module free from excessive dirt and debris. Use a soft, dry cloth for cleaning.
- معاینه: Periodically check wiring connections for corrosion or damage. Ensure the module remains securely mounted.
- د اوبو مقاومت: The module features an epoxy-potted design for water resistance, but it is not intended for submersion.
د ستونزو حل کول
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| Module not flashing / Lights not working | No power to the module; incorrect wiring; faulty lights; exceeded current limit. | Check power connections (red and black input wires). Verify all wiring is correct. Test lights directly. Ensure total current draw does not exceed 20 Amps. |
| Cannot change flash pattern | Momentary switch not connected or faulty; yellow wire connection issue. | Ensure the yellow wire is correctly connected to a functional momentary switch. Verify the switch provides a brief 12V positive signal when pressed. |
| Module stopped working after pattern change | Internal fault (rare). | If all wiring is confirmed correct and power is present, the module may be faulty. Contact Maxxima support for assistance. |
مشخصات
- ماډل: M50910
- والیtage: 12 ولټه DC
- Ampزمانه: 20 Amps Max (10 Amps per channel)
- د فلش نمونې: 16 د انتخاب وړ
- د محصول ابعاد: ۵.۴"L x ۵.۴"W x ۲.۸"H (۱۳.۷ سانتي متره L x ۱۳.۷ سانتي متره W x ۷.۱ سانتي متره H)
- د توکي وزن: ۱۶ اونس (تقریبا ۰.۴۵ کیلوګرامه)
- مواد: پلاستیک
- د نصب کولو ډول: بریکٹ ایونټ
- اصل: په تایوان کې جوړ شوی
تضمین او ملاتړ
The Maxxima M50910 LED Flasher Module typically comes with a one-year warranty from the date of purchase. For warranty claims, technical support, or further assistance, please contact Maxxima directly.
Maxxima Contact Information:
- پته: 125 Cabot Ct., Hauppauge, NY 11788 USA
- تلیفون: (631) 434-1200
- Webسایټ: Visit the Maxxima Store on Amazon (د عمومي محصول معلوماتو لپاره)
مهرباني وکړئ د تضمین موخو لپاره د پیرود ثبوت وساتئ.
