UHPPOTE HBK-A02 125KHz RFID Standalone Door Access Control Keypad User Manual

1. پیژندنه

This manual provides detailed instructions for the installation, programming, operation, and maintenance of the UHPPOTE HBK-A02 125KHz RFID Standalone Door Access Control Keypad. This device is designed to provide secure access control for various applications, supporting up to 1000 card users.

Figure 1: UHPPOTE HBK-A02 Keypad Front View

2. کلیدي ځانګړتیاوې

• High quality and high security, sensitively and response quickly.
• Full programming from the keypad, support add/delete cards, set password, etc.
• Door bell button support external doorbell.
• Uses high-performance MCU for stable performance and low-power circuit for extended service life.
• Functions as a standalone keypad, no computer connection required.
• Suitable for factories, houses, residential quarters, offices, and mechanical/electrical control equipment.

3. مشخصات

4. نصب کول

Proper installation is crucial for the optimal performance and security of your access control keypad. Ensure all power is disconnected before beginning installation.

۳.۲ د کیپډ نصبول

1. Choose a suitable mounting location near the door, ensuring it is protected from direct weather exposure if installed outdoors.
2. Use the provided mounting screws to secure the back plate of the keypad to the wall.
3. Route the necessary wiring through the wall or conduit to the keypad's connection point.
4. Attach the keypad front panel to the back plate after wiring is complete.

Figure 2: Keypad Mounted on a Door Frame

4.2 د تارونو نښلول

The HBK-A02 keypad requires a 12V DC power supply. Carefully follow the wiring diagrams below. Incorrect wiring can damage the device or connected components.

شکل 3: شاته View of Keypad with Wiring Harness

Figure 4: Close-up of Wiring Terminal Block

4.2.1 Common Power Supply Diagram

This diagram illustrates connections when using a single power supply for both the keypad and the electric lock.

Figure 5: Common Power Supply Wiring Diagram

4.2.2 Special Power Supply Diagram

This diagram shows connections when using a dedicated access control power supply unit, which often includes battery backup and advanced control features.

Figure 6: Special Power Supply Wiring Diagram

5 برنامه کول

The keypad is programmed directly using the numeric buttons. The default master code is 123456.

5.1 د پروګرام کولو حالت ته ننوتل

1. مطبوعاتي *.
2. Enter the 6-digit Master Code (default: 123456).
3. مطبوعاتي #.
4. The red LED will flash, indicating programming mode.

5.2 Exiting Programming Mode

مطبوعاتي * to exit programming mode at any time.

5.3 د ماسټر کوډ بدلول

1. د پروګرام کولو حالت ته ننوځئ.
2. مطبوعاتي 0.
3. Enter the new 6-digit Master Code.
4. Enter the new 6-digit Master Code again to confirm.
5. مطبوعاتي #.
6. د پروګرام کولو حالت څخه وتل.

5.4 Adding User Cards/Codes

The keypad supports up to 1000 user cards or codes.

1. د پروګرام کولو حالت ته ننوځئ.
2. مطبوعاتي 1.
3. For RFID cards: Present the card to the keypad. The keypad will beep to confirm. Repeat for additional cards.
4. For User Codes: Enter a 4-digit to 6-digit user code, then press #. Enter the code again and press # تصدیق کول.
5. د پروګرام کولو حالت څخه وتل.

5.5 Deleting User Cards/Codes

1. د پروګرام کولو حالت ته ننوځئ.
2. مطبوعاتي 2.
3. For RFID cards: Present the card to the keypad. The keypad will beep to confirm deletion. Repeat for additional cards.
4. For User Codes: Enter the 4-digit to 6-digit user code to delete, then press #.
5. د پروګرام کولو حالت څخه وتل.

5.6 Setting Relay Unlock Time

This sets how long the door remains unlocked after a valid access. The default is 5 seconds.

1. د پروګرام کولو حالت ته ننوځئ.
2. مطبوعاتي 3.
3. Enter a 2-digit number for the unlock time in seconds (e.g., 05 د 5 ثانیو لپاره ، 00 د 0.2 ثانیو لپاره).
4. مطبوعاتي #.
5. د پروګرام کولو حالت څخه وتل.

6. عملیات

6.1 Gaining Access

• Using an RFID Card: Present a registered RFID card to the keypad. The keypad will beep, and the door will unlock for the set duration.
• د کارن کوډ کارول: Enter your registered user code (4-6 digits) followed by #. The keypad will beep, and the door will unlock for the set duration.

6.2 Doorbell Function

فشار ورکړئ بیل button on the keypad to activate an external doorbell (if connected).

7. ساتنه

• پاکول: Wipe the keypad surface with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• د چاپیریال ساتنه: Ensure the keypad is protected from extreme temperatures, direct sunlight, and moisture to prolong its lifespan.
• منظم ازموینه: Periodically test the keypad's functionality, including card/code access and the exit button, to ensure proper operation.

8. ستونزه حل کول

9. د خوندیتوب معلومات

• تل د هر ډول تارونو یا ساتنې ترسره کولو دمخه بریښنا قطع کړئ.
• Ensure all wiring connections are secure and insulated to prevent short circuits.
• وسیله د اوبو یا ډیر رطوبت سره مه مخ کوئ.
• This device is intended for low-voltage applications (12V DC). Do not connect to higher voltagای سرچینې.
• Installation should be performed by qualified personnel if you are unsure about electrical wiring.