Axxess AX-TOYCAM2-6V Toyota Backup Camera Retention and Add-On Interface Manual

1. پیژندنه

The Axxess AX-TOYCAM2-6V is an interface designed to facilitate the retention of a factory backup camera or the addition of an aftermarket backup camera in select Toyota vehicles. This module includes an AX-CAM6V 12-volt to 6-volt converter, ensuring compatibility with factory camera systems that operate on a lower voltage. This manual provides essential information for proper installation, operation, and maintenance of the device.

2. د خوندیتوب معلومات

• Always disconnect the vehicle's negative battery terminal before beginning any installation to prevent electrical shorts and damage.
• د غوره فعالیت او خوندیتوب لپاره مسلکي نصب سپارښتنه کیږي.
• ډاډ ترلاسه کړئ چې ټولې اړیکې خوندي او په سمه توګه موصل شوي دي ترڅو د لنډ سرکټ مخه ونیول شي.
• Do not modify the harness or components unless explicitly instructed. Unauthorized modifications can void the warranty and cause damage.
• Route all wiring away from moving parts, heat sources, and sharp edges to prevent damage.

3. د بسته محتويات

Verify that all items are present before proceeding with the installation:

• Axxess AX-TOYCAM2-6V Interface Harness
• AX-CAM6V 12-volt to 6-volt Converter

The image below displays the main components of the AX-TOYCAM2-6V harness.

This image displays the Axxess AX-TOYCAM2-6V harness, featuring multiple connectors for integration with a Toyota vehicle's wiring system and an RCA connector for a backup camera. The harness includes red and black wires for power and ground connections, and a separate 6-volt converter.

4. ترتیب او نصب کول

This section outlines the general steps for installing the AX-TOYCAM2-6V interface. Specific vehicle wiring diagrams and disassembly instructions should be consulted for your particular Toyota model.

4.1 د نصب کولو دمخه مرحلې

1. د بیټرۍ قطع کول: د موټر د بیټرۍ منفي ټرمینل جلا کړئ.
2. د موټرو تارونو ته لاسرسی: Carefully remove the necessary trim panels and the factory head unit to gain access to the vehicle's wiring harness.

4.2 د هارنس اتصال

3. Connect Interface Harness: Connect the AX-TOYCAM2-6V harness to the corresponding factory connectors behind the head unit. Ensure all connections are firm and secure.
4. Connect 6-Volt Converter (AX-CAM6V): If retaining a factory camera or adding a camera requiring 6V, connect the AX-CAM6V converter. The typical wiring for the converter is:
   • نیلي/سپین تار: 12V Input (Connect to a switched 12V source).
   • Blue/Red Wire: 6V Output (Connect to the camera's 6V power input).
   • تور تار: Ground (Connect to a reliable chassis ground).
5. Connect Camera (if adding): Connect the aftermarket backup camera's video output (RCA) to the yellow RCA input on the AX-TOYCAM2-6V harness.

۴.۳ د نصبولو وروسته مرحلې

6. د ازموینې فعالیت: Reconnect the vehicle's battery. Turn on the ignition and engage reverse gear to test the backup camera display. Verify that the image is clear and activates correctly.
7. بیا یوځای کول: Once functionality is confirmed, carefully reassemble all removed trim panels and secure the head unit.

The following video demonstrates the physical appearance of the harness, which can assist in identifying components during installation.

5. عملیاتي لارښوونې

The Axxess AX-TOYCAM2-6V interface operates automatically. Once correctly installed, the connected backup camera will display its image on the vehicle's screen when the transmission is shifted into reverse gear. No manual intervention is required for its basic operation.

6. ساتنه

The AX-TOYCAM2-6V is a low-maintenance electronic component. To ensure its longevity and reliable performance:

• په دوره یي ډول د ټولو تارونو اتصالونه وګورئ ترڅو ډاډ ترلاسه شي چې دوی خوندي او له زنګ څخه پاک دي.
• د موډل د تودوخې یا رطوبت له څرګندولو څخه ډډه وکړئ.
• Do not attempt to open or service the module yourself. Refer to qualified technicians for any issues beyond basic troubleshooting.

7. ستونزه حل کول

If you encounter issues with your backup camera system after installing the AX-TOYCAM2-6V, consider the following troubleshooting steps:

7.1 No Camera Display

• ځواک چیک کړئ: Ensure the 12V input to the AX-CAM6V converter is receiving power when the vehicle is in reverse. Verify the ground connection.
• اړیکې تایید کړئ: Double-check all harness connections to the factory wiring and the camera's RCA input.
• د کیمرې فعالیت: Test the backup camera directly if possible, to rule out a faulty camera.

7.2 Distorted or Intermittent Image

• Inspect RCA Cable: Ensure the RCA video cable is not damaged, pinched, or routed near high-voltage wires that could cause interference.
• خوندي اړیکې: Confirm all video connections are tight and free from corrosion.
• د بریښنا ثبات: Verify that the 6V output from the AX-CAM6V converter is stable.

If problems persist after performing these checks, contact Axxess technical support or a qualified installer.

8. مشخصات

9. د تضمین معلومات

Axxess products are covered by a manufacturer's warranty. For specific details regarding the warranty period, coverage, and claims process for the AX-TOYCAM2-6V, please refer to the warranty documentation included with your purchase or visit the official Axxess webسایټ. د تضمین تصدیق لپاره د پیرود ثبوت وساتئ.

10. ملاتړ

For technical assistance, installation questions, or further support regarding the Axxess AX-TOYCAM2-6V, please contact Axxess customer support directly. You can typically find contact information on the Axxess webسایټ یا د محصول بسته بندي کې.

Axxess Official Webسایټ: https://axxessinterfaces.com/ (Please note: This is a general placeholder link, verify the current official support website for Axxess.)