Chief FTR100 Tilting Hardware Mount User Manual

۱.۱. د خوندیتوب مهم معلومات

Read all instructions carefully before installation and use. Failure to follow these instructions may result in property damage, serious injury, or death. If you do not understand these instructions, or have doubts about the safety of the installation, contact a qualified installer.

• د وزن ظرفیت: This mount is designed for flat panel displays up to 32 inches. Do not exceed the maximum weight capacity specified by the manufacturer.
• د دیوال جوړښت: Ensure the mounting surface can safely support the combined weight of the equipment and hardware. Use appropriate fasteners for the wall type (wood stud, concrete, brick, etc.).
• مسلکي نصب کول: For optimal safety, professional installation is recommended.
• خوځنده برخې: Exercise caution when adjusting the tilt mechanism to avoid pinching or injury.

2. د بسته محتويات

د نصبولو دمخه ډاډ ترلاسه کړئ چې ټولې برخې شتون لري او زیانمنې شوې نه دي. که کومه برخه ورکه یا زیانمنه شوې وي، د نصبولو هڅه مه کوئ او د پیرودونکي ملاتړ سره اړیکه ونیسئ.

• Flat Panel Wall Mount (FTR100)
• Mounting Hardware Kit (screws, washers, anchors - specific contents may vary)
• د نصبولو لارښوونې (دا سند)

3. ترتیب او نصب کول

This section provides step-by-step instructions for mounting your Chief FTR100 Tilting Hardware Mount.

3.1 د نصب کولو دمخه چکونه

1. Identify the desired mounting location. Ensure there are no hidden electrical wires or plumbing.
2. Confirm the wall type (wood stud, concrete, brick) and select appropriate mounting hardware.
3. Measure the VESA mounting pattern on your flat panel display to ensure compatibility with the FTR100 mount.

۴.۲ د دیوال پلیټ نصب کول

1. Position the wall plate at the desired height and mark the drilling locations. Use a level to ensure accuracy.
2. Drill pilot holes according to the recommended drill bit size for your chosen fasteners and wall type.
3. Secure the wall plate to the wall using the provided mounting hardware. Ensure all screws are tightened securely.

3.3 Attaching the Display to the Mount

1. Attach the display brackets to the back of your flat panel display using the appropriate screws from the hardware kit. Ensure they are securely fastened.
2. Carefully lift the display and hook the display brackets onto the wall plate. The FTR100 utilizes a Q-Latch mounting system for secure attachment.
3. Engage the Q-Latch mechanism to lock the display onto the wall plate. Refer to the specific latching instructions provided with the hardware kit.
4. The mount can be used in either a horizontal or vertical orientation, depending on your display and application.

شکل 1: Chief FTR100 Tilting Hardware Mount. This image shows the overall design of the mount, including the wall plate and display brackets, ready for installation.

۳. د غره چلول

The Chief FTR100 mount allows for tilting adjustments to achieve optimal viewزاویې

4.1 Tilting the Display

Once the display is securely mounted, you can adjust its tilt angle. The FTR100 offers a maximum tilt angle of 15 degrees.

1. Gently grasp the top or bottom edge of the display.
2. Carefully push or pull the display to achieve the desired tilt angle. The mount is designed to hold the position once set.
3. Avoid excessive force when tilting. If the display does not move smoothly, check for obstructions or consult the troubleshooting section.

5. ساتنه

Regular maintenance helps ensure the longevity and safe operation of your mount.

• پاکول: د غره د پاکولو لپاره نرم، وچ ټوکر وکاروئ. د کثافاتو پاکوونکو یا محلولونو څخه ډډه وکړئ چې کولی شي پای ته زیان ورسوي.
• وختي معاینات: په دوره یي ډول ټول نصب شوي پیچونه او اړیکې معاینه کړئ ترڅو ډاډ ترلاسه شي چې دوی کلک او خوندي پاتې دي. که اړتیا وي نو بیا کلک کړئ.
• خوځنده برخې: The tilting mechanism is designed for smooth operation. If it becomes stiff, do not apply lubricants unless specifically recommended by Chief Mfg.

6. ستونزه حل کول

This section addresses common issues you might encounter with your Chief FTR100 mount.

• Display is not level:
  • Check the wall plate installation. Ensure it was installed using a level.
  • Verify that the display brackets are evenly attached to the back of the display.
• Difficulty tilting the display:
  • ډاډ ترلاسه کړئ چې هیڅ کیبل د خښتو میکانیزم خنډ نه کوي.
  • Confirm the display weight is within the specified limits for the mount.
• غره خلاص احساس کوي:
  • Immediately remove the display.
  • Re-tighten all wall plate and display bracket screws. If the issue persists, consult a professional installer.

7. مشخصات

Detailed technical specifications for the Chief FTR100 Tilting Hardware Mount.

8. تضمین او ملاتړ

For warranty information, technical support, or to inquire about replacement parts, please contact Chief Manufacturing directly. Refer to the official Chief webد اوسني اړیکو توضیحاتو او تضمین شرایطو لپاره سایټ یا ستاسو د پیرود اسناد.

جوړونکی: Chief Mfg.

Webسایټ: www.legrandav.com/products/chief (This is a common URL for Chief products, please verify with official documentation)