وینګارډ VEO 2 235AP المونیم ټریپډ د VEO 2 PH-25 پین سر کارونکي لارښود سره

1. پیژندنه

The Vanguard VEO 2 235AP is a versatile aluminum tripod designed for photographers and outdoor enthusiasts. It features a VEO 2 PH-25 pan head, offering precise control for both still photography and video. This manual provides essential information for the proper setup, operation, and maintenance of your tripod to ensure optimal performance and longevity.

2. د خوندیتوب معلومات

• Always ensure all leg locks and head controls are securely tightened before mounting equipment.
• Do not exceed the maximum weight capacity of 7.7 pounds (3.5 kg) to prevent damage to the tripod or your equipment.
• Be cautious when extending or retracting legs to avoid pinching fingers.
• د تپېډ د سختې تودوخې یا زنګ وهونکو موادو سره د مخ کیدو څخه ډډه وکړئ.
• Do not leave the tripod unattended in windy conditions, especially with heavy equipment mounted. Use the suspension loop for added stability if needed.

3. د بسته محتويات

ډاډ ترلاسه کړئ چې ټول توکي ستاسو په کڅوړه کې شتون لري:

• Vanguard VEO 2 235AP Aluminum Tripod with VEO 2 PH-25 Pan Head
• د بار وړلو کڅوړه

4. ترتیب کول

4.1 Unpacking and Initial Deployment

Carefully remove the tripod from its packaging and the carrying bag. The tripod is designed for quick setup. Swing the central column into its upright position and ensure it locks securely.

Figure 1: Vanguard VEO 2 235AP Tripod in extended position.

4.2 Leg Extension and Angle Adjustment

The tripod features 5-section aluminum legs with an advanced twist lock system. To extend a leg, rotate the twist lock counter-clockwise to loosen, pull the leg section to the desired length, and then rotate clockwise to tighten securely. Repeat for all sections and legs.

Leg angles can be independently adjusted to 20°, 45°, or 80° by pressing the angle lock release button at the top of each leg and setting it to the desired position. This allows for stable positioning on uneven terrain or for low-angle photography.

4.3 Attaching the Pan Head (if separate)

The VEO 2 PH-25 pan head is typically pre-attached to the central column. If it needs to be attached or re-attached, ensure the mounting screw on the central column is aligned with the pan head's base and rotate the head clockwise until it is firmly secured.

2 شکل: تړل view of the VEO 2 PH-25 Pan Head with control knobs.

4.4 Quick Release Plate Attachment

The VEO 2 PH-25 pan head uses an Arca-type compatible quick release plate. Attach this plate to the tripod mount screw on the bottom of your camera or spotting scope. Ensure it is tightened securely to prevent rotation.

5. چلول

5.1 د کیمرې نصب کول

With the quick release plate attached to your equipment, slide the plate into the receiver on the pan head. Secure it by engaging the locking lever or knob on the pan head. Always double-check that your equipment is firmly seated before releasinستاسو گرفت.

Figure 3: Vanguard VEO 2 235AP Tripod with a camera mounted on the pan head.

5.2 Pan Head Controls

The VEO 2 PH-25 pan head features two independent control knobs:

• Tilt Lock Knob: Controls the vertical (tilt) movement of the head. Loosen to adjust the angle, tighten to lock in position.
• د پیننګ قلف نوب: Controls the horizontal (pan) rotation of the head. Loosen to rotate, tighten to lock.

The quick-fold handle can be folded down for compact transport.

5.3 د قد تنظیم کول

Adjust the height by extending the leg sections as described in Section 4.2. The central column can also be extended for additional height. Ensure the central column lock is tightened after adjustment. The maximum extended height is 56.75 inches.

5.4 Low Angle Photography

For very low-angle shots, utilize the 80° leg angle setting. The central column can also be inverted or removed and re-inserted from below (if applicable to your model) to achieve ground-level perspectives.

5.5 Enhancing Stability

For increased stability, especially in windy conditions or with heavier loads, use the dedicated suspension loop located on the tripod's canopy. You can hang a camera bag or other weights from this loop to lower the center of gravity.

Figure 4: Tripod in use, demonstrating stability for a spotting scope.

6. ساتنه

6.1 پاکول

Clean the tripod regularly with a soft, damp ټوکر. د سختې خاورې لپاره، د صابون یو نرم محلول کارول کیدی شي، وروسته د پاک، d سره مسح کول.amp cloth. Ensure all parts are thoroughly dried. Avoid using harsh chemicals or abrasive cleaners, which can damage the finish or components.

6.2 ذخیره کول

When not in use, fold the tripod to its most compact size (15.75 inches) and store it in the provided carrying bag. Store in a dry, cool environment away from direct sunlight and excessive humidity.

Figure 5: Tripod stored compactly in its carrying bag.

6.3 Twist Lock Care

Periodically inspect the twist lock mechanisms for any accumulation of dirt, sand, or debris. Clean them gently to ensure smooth operation and secure locking of the leg sections. Do not over-tighten the locks, as this can cause premature wear.

7. ستونزه حل کول

• بې ثباتي: Ensure all leg sections are fully extended and twist locks are securely tightened. Verify leg angles are set correctly for the terrain. Add weight to the suspension hook if necessary.
• Stiff Pan Head Movement: If the pan head movement is stiff, check for debris around the pivot points and ensure the control knobs are not overtightened. Clean as per maintenance instructions.
• کیمره خوندي نه ده: Ensure the quick release plate is properly seated in the pan head receiver and the locking lever is fully engaged. Confirm the plate is tightly secured to your camera.

8. مشخصات

Figure 6: Folded and extended dimensions of the VEO 2 235AP Tripod.

9. تضمین او ملاتړ

For detailed warranty information, product registration, and customer support, please visit the official Vanguard webسایټ یا د دوی د پیرودونکو خدماتو څانګې سره اړیکه ونیسئ. تاسو کولی شئ نور معلومات او محصولات په کې هم ومومئ د وینګارډ رسمي پلورنځی.