1. پیژندنه
This document provides detailed instructions for the Waveshare 4.2inch E-Ink Display Module. This module features a 400x300 resolution and communicates via an SPI interface. Its design offers ultra-low power consumption, a wide viewing angle, and maintains a clear display without continuous power, making it suitable for applications such as electronic shelf labels and industrial instrumentation.
شکل 1: مخکی view of the 4.2inch E-Ink Display Module.
2. ځانګړتیاوې
- No Backlight Required: The display retains its content indefinitely even when power is removed.
- د برېښنا ډېر ټیټ مصرف: Power is primarily consumed only during display refreshes.
- د SPI انٹرفیس: Facilitates connection with various controller boards, including Raspberry Pi, Arduino, and Nucleo.
- د الوتکې ټوکtage Translator: Ensures compatibility with both 3.3V and 5V microcontrollers (MCUs).
- د پراختیا سرچینې: Online user manuals and example code are provided for Raspberry Pi, Jetson Nano, Arduino, and STM32 platforms.
۲. په بکس کې څه دي؟
په بسته کې لاندې برخې شاملې دي:
- 1x Waveshare 4.2inch e-Paper Module
- ۱x PH2.0 ۲۰ سانتي متره ۸ پن کیبل
Figure 2: Contents of the package, including the display module and connecting cable.
4. مشخصات
| پیرامیټر | ارزښت |
|---|---|
| د ښودلو اندازه | 4.2 انچه |
| قرارداد | 400 x 300 پکسله |
| رنګ ښکاره کړئ | تور / سپین |
| خړ سکیل | 4 |
| د عملیاتو Voltage | 3.3V / 5V |
| انٹرفیس | درې تاره SPI، څلور تاره SPI |
| د بڼې ابعاد | 103.0mm x 78.5mm |
| د ښودلو ساحه | 84.8mm x 63.6mm |
| ډوټ پچ | 0.212 x 0.212 mm |
| بشپړ تازه کولو وخت | نږدې 4 ثانیې |
| د تازه کولو جزوي وخت | نږدې 0.4 ثانیې |
| د بریښنا مصرف تازه کړئ | ۲۶.۴ میګاواټه (معمولي) |
| د سټینډ بای بریښنا مصرف | <0.017mW |
| Viewزاویه | >170° |
Figure 3: Module overview, interface details, and dimensions.
5. تنظیم او پیوستون
The 4.2inch E-Ink Display Module connects to a host microcontroller via a Serial Peripheral Interface (SPI). Ensure correct pin connections to prevent damage to the module or host device.
5.1. د پن تعریفونه
Refer to the following table and diagram for the pin assignments:
| پن | تفصیل |
|---|---|
| VCC | Power supply (3.3V-5V) |
| GND | ځمکه |
| DIN | SPI MOSI (Master Out Slave In) pin |
| CLK | د SPI SCK (سیریل کلاک) پن |
| CS | SPI Chip Select, active low |
| DC | Data/Command selection (High for data, Low for command) |
| RST | External Reset, active low |
| بوخت | Busy status output, active high when busy |
Figure 4: Back of the module with pinout labels (Revision 2.1 shown).
5.2. د پیوستون کړنلاره
- Identify the corresponding SPI pins (VCC, GND, DIN, CLK, CS, DC, RST, BUSY) on your host microcontroller (e.g., Raspberry Pi, Arduino).
- Connect the included 8-pin cable to the module's connector.
- Carefully connect each wire from the cable to the correct pin on your microcontroller. Double-check all connections before applying power.
- Ensure your microcontroller's logic level is compatible with the module's operating voltage (3.3V or 5V). The onboard voltage translator handles this automatically.
6. عملیات
The Waveshare 4.2inch E-Ink Display Module operates on the principle of electrophoretic display technology. This means it does not require a backlight and can hold an image indefinitely without power. Content updates require a refresh cycle, during which power is consumed.
6.1. Display Refresh
- بشپړ تازه کول: A complete screen update typically takes around 4 seconds. This clears the entire display and redraws new content.
- جزوي تازه کول: For minor updates to specific areas of the screen, a partial refresh can be used, which is significantly faster, approximately 0.4 seconds. This mode is useful for dynamic content that changes frequently without needing a full screen clear.
5 شکل: یو پخوانیample image displayed on the E-Ink module.
Figure 6: The E-Ink display module in a blank state.
7. ساتنه
E-Ink displays are generally low-maintenance. To ensure longevity and optimal performance:
- د اوږدې مودې لپاره د لوړې تودوخې یا مستقیم لمر وړانګو ته د نندارې د افشا کولو څخه ډډه وکړئ.
- Do not apply excessive pressure to the display surface.
- Clean the display surface gently with a soft, dry, lint-free cloth. Avoid using liquid cleaners or abrasive materials.
- Store the module in a dry, dust-free environment when not in use.
8. ستونزه حل کول
If you encounter issues with your E-Ink display module, consider the following common troubleshooting steps:
- No Display/Garbled Output:
- Verify all SPI connections (VCC, GND, DIN, CLK, CS, DC, RST, BUSY) are correct and secure. Incorrect wiring is a common cause of display issues.
- Ensure the power supply to the module is within the specified 3.3V-5V range.
- Check that the correct software library and driver are being used for the 4.2inch 400x300 E-Ink display. Refer to Waveshare's online resources for specific examples.
- Confirm that the reset (RST) and busy (BUSY) pins are correctly handled in your code.
- ورو تازه کولو کچه:
- Full refreshes are inherently slower than partial refreshes. If you are performing frequent updates, consider implementing partial refresh functionality in your code.
- Ensure your SPI clock speed is configured correctly and is not excessively slow.
- Display Not Clearing Completely:
- Sometimes, residual ghosting can occur. Performing a full refresh cycle multiple times may help clear the display.
- Ensure your software is sending the correct commands for a full clear before drawing new content.
۳.۱. ملاتړ او سرچینې
For further assistance, detailed documentation, and development examples, please refer to the official Waveshare online resources. These resources typically include comprehensive user manuals, schematics, and code examples for various platforms like Raspberry Pi, Jetson Nano, Arduino, and STM32.
د ویوشیر چارواکي ته مراجعه وکړئ website or product page for the latest support information and downloads.
