MEXTECH DT1503 Digital Capacitance Meter User Manual

1. پیژندنه

د پیرودلو لپاره مننهasing the MEXTECH DT1503 Digital Capacitance Meter. This precision instrument is designed for accurate capacitance measurements across a wide range, suitable for laboratory, factory, and educational use. Please read this manual thoroughly before operating the device to ensure safe and correct usage.

د بسته محتويات:

• MEXTECH DT1503 Digital Capacitance Meter
• One Set Test Leads
• 1pc 9V Battery
• د لارښود لارښود (دا سند)

The image above shows the MEXTECH DT1503 Digital Capacitance Meter along with its included accessories: a set of test leads, a 9V battery, and the user manual.

2. د خوندیتوب معلومات

WARNING: To avoid electrical shock, do not operate the meter with the battery cover open.

CAUTION: This device complies with IEC61010-1 standards, rated for 1000V CAT II and 600V CAT III, Pollution Degree 2. Always adhere to safety guidelines.

• Always ensure the capacitor under test is fully discharged before connecting it to the meter.
• Do not attempt to measure capacitance in live circuits.
• Inspect test leads for damage before each use. Replace if damaged.
• که چیرې میټر خراب ښکاري یا په سمه توګه کار نه کوي نو مه یې کاروئ.
• ټول خدمتونه وړ پرسونل ته راجع کړئ.

The image displays the back of the MEXTECH DT1503 meter, highlighting important safety warnings and compliance information printed on the battery compartment cover.

3. د محصول ب Featuresې

The MEXTECH DT1503 Digital Capacitance Meter offers the following key features:

• ښکاره کول: 3½ Digit LCD with 1999 counts.
• د اندازه کولو لړۍ: Wide range from 200pF up to 20mF.
• واحدونه: Four measuring units: pF, nF, µF, mF.
• شاته رڼا: Automatic shutdown after 10 seconds to conserve battery.
• د معلوماتو ساتل: Function to freeze the displayed reading.
• صفر تعدیل: Knob for precise zero adjustment across all ranges.
• د ټیټ بیټرۍ نښې: کله چې د بیټرۍ بدلولو ته اړتیا وي نو خبرتیاوې.
• د فیوز ساتنه: Ensures safety and protects the internal circuitry.
• د بریښنا رسول: Operates on a single 9V battery.

دا انځور یو روښانه view of the meter's front panel, including the LCD display, rotary function switch, 'LIGHT' and 'HOLD' buttons, and the 'ADJ' knob for zero adjustment.

4. ترتیب کول

4.1 د بیټرۍ نصب کول

1. Ensure the meter is turned OFF by rotating the function switch to the 'OFF' position.
2. د میټر په شا کې د بیټرۍ کڅوړه ومومئ.
3. Open the battery cover by sliding or unscrewing it (refer to Figure 2).
4. Insert one 9V battery, observing the correct polarity (+ and - terminals).
5. د بیټرۍ پوښ په خوندي ډول وتړئ.

۶.۲ د ټیسټ لیډونو نښلول

1. Insert the red test lead plug into the 'CX+' input terminal.
2. Insert the black test lead plug into the 'COM' input terminal.

This image shows the MEXTECH DT1503 meter with the red test lead connected to the 'CX+' terminal and the black test lead connected to the 'COM' terminal, ready for measurement.

5. عملیاتي لارښوونې

۸ پاور آن/بند

To turn the meter ON, rotate the rotary function switch from the 'OFF' position to any desired measurement range. To turn the meter OFF, rotate the switch back to the 'OFF' position.

5.2 صفر تعدیل

Before performing any capacitance measurement, especially on lower ranges, it is crucial to perform a zero adjustment to eliminate stray capacitance from the test leads and internal circuitry.

1. Ensure the test leads are connected to the meter.
2. Short the tips of the red and black test leads together.
3. Rotate the 'ADJ' knob (located on the left side of the meter) until the display reads '000'.
4. This adjustment should be performed for each range if significant deviation from zero is observed.

5.3 د ظرفیت اندازه کول

1. د خارجولو کپاسیټر: Always ensure the capacitor to be measured is fully discharged before connecting it to the meter. Failure to do so can damage the meter or cause injury.
2. سلسله وټاکئ: Rotate the function switch to the appropriate measurement range. If the capacitance value is unknown, start with the highest range (20mF) and work downwards until a stable and accurate reading is obtained.
3. Connect Capacitor: Connect the test leads to the capacitor terminals. For polarized capacitors (e.g., electrolytic), connect the red lead to the positive terminal and the black lead to the negative terminal. For non-polarized capacitors, the connection order does not matter.
4. د لوستلو ارزښت: The capacitance value will be displayed on the LCD screen in the selected unit (pF, nF, µF, or mF).

5.4 د ډیټا هولډ فعالیت

To freeze the current reading on the display, press the 'HOLD' button. The 'HOLD' indicator will appear on the screen. Press the 'HOLD' button again to release the reading and resume live measurement.

5.5 شالید

Press the 'LIGHT' button to activate the display backlight. This feature is useful for reading measurements in low-light conditions. The backlight will automatically turn off after approximately 10 seconds to conserve battery power.

۸.۱. د اندازه کولو حدود او دقت

The MEXTECH DT1503 offers the following measurement ranges and typical accuracy specifications:

7. ساتنه

7.1 پاکول

To clean the meter, wipe the casing with a dry, soft cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the plastic components or electronic circuits.

7.2 د بیټرۍ بدلول

When the low battery indicator appears on the display, the 9V battery needs to be replaced. Follow the steps outlined in Section 4.1 'Battery Installation'. Ensure the meter is OFF before replacing the battery.

7.3 د فیوز بدلول

If the meter fails to function or provides incorrect readings consistently, the internal fuse may need replacement. Fuse replacement should only be performed by a qualified technician to ensure the correct fuse type and rating are used. Opening the meter by unauthorized personnel may void the warranty.

8. ستونزه حل کول

This section addresses common issues you might encounter with your MEXTECH DT1503 meter.

• نه ښودنه یا کمزوری ښودنه:
  حل لاره: Check the 9V battery. Ensure it is correctly installed and has sufficient charge. Replace the battery if necessary. Also, ensure the rotary switch is not in the 'OFF' position.
• Incorrect or Unstable Readings:
  حل لاره: Perform a zero adjustment as described in Section 5.2. Ensure the test leads are properly connected and not damaged. Verify that the capacitor under test is fully discharged. Select the correct measurement range; if the range is too high for a small capacitor, the reading may be unstable or show '000'.
• Low Battery Indicator Appears:
  حل لاره: Replace the 9V battery immediately to ensure accurate measurements and proper operation.
• میټر ځواب نه ورکوي:
  حل لاره: Check the battery. If the battery is good, the internal fuse might be blown. Refer to Section 7.3 for fuse replacement. If the issue persists, contact customer support.

9. مشخصات

10. تضمین او ملاتړ

For warranty information, technical assistance, or service inquiries regarding your MEXTECH DT1503 Digital Capacitance Meter, please refer to the warranty card included with your product or visit the official MEXTECH webد اړیکو توضیحاتو او ملاتړ سرچینو لپاره سایټ.