ICON 12511 فټینګ، هب، 3" - د لارښوونې لارښود

1. محصول ختم شوview

The ICON 12511 Hub Fitting is designed to facilitate the transition from polyethylene holding tanks to standard ABS plumbing systems. This essential component ensures a secure and leak-free connection in RV waste water and sanitation setups.

Image: The ICON 12511 3-inch Hub Fitting. This black, polyethylene fitting is cylindrical, featuring a wider opening at the top for connection to a holding tank and a narrower section at the bottom for ABS plumbing. An O-ring is included for a secure seal.

۲. په بکس کې څه دي؟

The package for the ICON 12511 Fitting, Hub, 3" includes the following components:

• One (1) ICON 12511 Holding Tank Fitting 3" Hub Fitting
• One (1) O-ring (pre-installed or included for the 3" female slip end)

3. ترتیب او نصب کول

This section provides instructions for the proper installation of the ICON 12511 Hub Fitting. Ensure all safety precautions are followed during installation.

3.1. Required Materials (Not Included)

• Butyl sealant (ICON part # 12062 recommended)
• Hose pipe clamp (appropriate size for 3" connection)
• Standard ABS plumbing adhesive/cement (for ABS connections)

3.2. د نصبولو پړاوونه

1. Prepare the Holding Tank: Ensure the polyethylene holding tank has a molded collar suitable for a 3-inch hub connection. Clean the area around the collar thoroughly to remove any debris or residue.
2. سیلانټ تطبیق کړئ: Apply a generous amount of butyl sealant (e.g., ICON part # 12062) around the molded polyethylene collar of the holding tank. This will create a watertight seal between the tank and the hub fitting.
3. Attach the Hub Fitting: Carefully slide the ICON 12511 Hub Fitting onto the molded polyethylene collar of the holding tank. Ensure the O-ring is properly seated within the female slip end of the hub to provide an initial seal.
4. د Cl سره خوندي کړئamp: Place a hose pipe clamp around the connection point where the hub fitting meets the holding tank's collar. Tighten the clamp securely to compress the butyl sealant and create a robust, leak-proof connection.
5. Connect to ABS Plumbing: The 3-inch female slip end of the hub fitting is designed for connection to standard ABS plumbing. Use appropriate ABS plumbing adhesive/cement to join the hub fitting to your ABS drain pipe. Follow the adhesive manufacturer's instructions for curing times.
6. د لیکونو لپاره ازموینه: After the adhesive has cured, fill the holding tank with water and inspect all connections for any signs of leaks. Address any leaks immediately before putting the system into full operation.

4. عملیات

The ICON 12511 Hub Fitting is a passive component designed to facilitate fluid transfer. Once properly installed, its operation is integrated with the overall RV waste water system. Ensure that all connected plumbing components are functioning correctly to allow for proper waste drainage.

5. ساتنه

Regular inspection of the ICON 12511 Hub Fitting and surrounding plumbing is recommended to ensure long-term performance and prevent issues.

• بصری معاینه: Periodically check the hub fitting and its connections for any signs of cracks, wear, or leaks. Pay close attention to the areas where the butyl sealant and hose clamp are applied, as well as the ABS plumbing joints.
• پاکوالی: While the fitting itself is part of a waste system, ensuring the exterior is free from excessive dirt or debris can help in visual inspections.
• د مهر بشپړتیا: If any leaks are detected, re-evaluate the application of the butyl sealant and the tightness of the hose pipe clamp. If necessary, disassemble, clean, reapply sealant, and re-secure the connection.

6. ستونزه حل کول

This section addresses common issues that may arise with the ICON 12511 Hub Fitting.

• Leakage at Tank Connection:
  • لامل: Insufficient butyl sealant, improperly seated O-ring, or loose hose pipe clamp.
  • حل لاره: Ensure adequate butyl sealant is applied. Verify the O-ring is correctly positioned. Tighten the hose pipe clamp. If leakage persists, disassemble, clean surfaces, reapply sealant, and reassemble.
• Leakage at ABS Plumbing Connection:
  • لامل: Improper application of ABS adhesive/cement, insufficient curing time, or damaged ABS pipe.
  • حل لاره: Ensure proper technique for ABS cementing. Allow sufficient curing time as per adhesive manufacturer's instructions. Inspect ABS pipe for damage and replace if necessary.
• Difficulty Connecting to Tank/Plumbing:
  • لامل: Incorrect sizing, debris in connection points, or manufacturing defect.
  • حل لاره: Verify that the tank collar and ABS pipe are indeed 3-inch compatible. Clean all connection surfaces. If the issue persists and sizing is correct, contact ICON customer support.

7. مشخصات

8. تضمین او ملاتړ

For information regarding product warranty, returns, or technical support, please contact ICON Technologies Limited directly. Refer to the original product packaging or the manufacturer's official webد اړیکو د تازه جزیاتو او تضمین پالیسۍ لپاره سایټ.

جوړونکی: Icon Technologies Limited

Webسایټ: Visit the ICON Store on Amazon (د عمومي برانډ معلوماتو لپاره)