1. پیژندنه
This manual provides essential information for the proper installation, operation, and maintenance of your True Manufacturing GDM-49-HC~TSL01 Glass Door Merchandiser. Please read these instructions thoroughly before operating the unit to ensure safe and efficient performance. Retain this manual for future reference.
2. د خوندیتوب معلومات
خبرداری: د بریښنا شاک خطر. د خدمت کولو دمخه بریښنا قطع کړئ.
- ډاډ ترلاسه کړئ چې د بریښنایی خطرونو مخنیوي لپاره واحد په سمه توګه مینځل شوی.
- په دې وسیله کې چاودیدونکي توکي لکه ایروسول کین د اور اخیستونکي پروپیلنټ سره مه ذخیره کوئ.
- د وسیلې په بند کې یا په جوړ شوي جوړښت کې د وینټیلیشن خلاصې له خنډ څخه پاک وساتئ.
- د ډیفروسټ کولو پروسې ګړندۍ کولو لپاره میخانیکي وسایل یا نور وسیلې مه کاروئ ، پرته لدې چې د تولید کونکي لخوا وړاندیز شوي.
- د یخچال سرکټ ته زیان مه رسوئ.
- یوازې د وړ خدماتو پرسونل باید ترمیم ترسره کړي.
3. ترتیب او نصب کول
3.1 پیک کول
Carefully remove all packaging materials, including tape and protective film. Inspect the unit for any shipping damage. Report any damage immediately to the carrier and your dealer.
3.2 ځای پرځای کول
Position the merchandiser on a strong, level surface capable of supporting its weight when fully loaded. Ensure adequate clearance around the unit for proper ventilation. Avoid direct sunlight or proximity to heat-generating equipment.
شکل 1: مخکی view of the True Manufacturing GDM-49-HC~TSL01 Glass Door Merchandiser.
3.3 سطحي کول
Use a level to ensure the unit is perfectly level. Adjust the leveling feet at the bottom of the unit as needed. Proper leveling is crucial for door alignment and efficient operation.
3.4 بریښنایی پیوستون
Connect the merchandiser to a dedicated, properly grounded electrical outlet. Refer to the unit's data plate for specific voltage او amperage requirements. Do not use extension cords.
3.5 د شیلف نصب کول
The unit comes with 8 adjustable wire shelves. Install them by inserting the shelf clips into the desired slots on the vertical pilasters inside the cabinet. Ensure all clips are securely seated and the shelves are level before loading products.
Figure 2: Technical drawing illustrating dimensions and features of the GDM-49-HC~TSL01.
4. عملیاتي لارښوونې
4.1 ابتدايي پیل
After connecting to power, allow the unit to run for several hours empty to reach its operating temperature before loading products. The factory-set temperature range is typically 33°F to 38°F (0.5°C to 3.3°C).
4.2 د تودوخې کنټرول
The merchandiser features an electronic control system. Adjust the temperature settings using the digital display and buttons, typically located on the front or side of the unit. Refer to the control panel instructions for precise adjustments.
۵.۳ د محصولاتو بارول
Load products evenly on the shelves, ensuring not to block the internal airflow or exceed the shelf weight capacity. Avoid placing items directly against the back wall to maintain proper air circulation.
4.4 د دروازې عملیات
The unit is equipped with self-closing glass doors. Ensure doors close completely after each use to maintain internal temperature and energy efficiency. The doors feature a positive seal torsion type closure system.
5. ساتنه
5.1 د کور دننه پاکول
Regularly clean the interior surfaces with a mild soap and water solution. Rinse thoroughly and dry with a clean cloth. Do not use abrasive cleaners or sharp objects that could damage the surfaces.
5.2 د بهر پاکول
Wipe down the exterior with a soft cloth and mild detergent. For stainless steel surfaces, use a non-abrasive cleaner designed for stainless steel, wiping in the direction of the grain.
۵.۳ د کنډنسر کویل پاکول
The condenser coil should be cleaned regularly (monthly or quarterly, depending on environment) to ensure optimal performance and energy efficiency. Disconnect power before cleaning. Use a stiff brush or vacuum cleaner to remove dust and debris from the coil. An easily accessible condenser coil is located at the bottom front of the unit.
۵.۲ د ګازکیټ معاینه
Periodically inspect the door gaskets for tears or damage. Ensure they form a tight seal when the doors are closed. Replace damaged gaskets promptly to prevent air leakage and maintain efficiency.
5.5 اتوماتیک ډیفروسټ
This unit features an automatic defrost system, eliminating the need for manual defrosting. Ensure the drain pan is clear and free of obstructions.
6. ستونزه حل کول
مخکې له دې چې له خدماتو سره اړیکه ونیسئ، بیاview لاندې عامې ستونزې او حل لارې:
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| واحد یخ نه کوي | Power supply issue, thermostat setting, dirty condenser coil, blocked airflow | Check power connection, adjust thermostat, clean condenser, ensure proper loading. |
| ډیر شور | Loose components, fan obstruction, unit not level | Inspect for loose parts, clear fan area, level the unit. |
| دروازې په سمه توګه نه تړل کېږي | Obstructed hinges, damaged gaskets, unit not level | Clear obstructions, inspect/replace gaskets, level the unit. |
| په فرش کې اوبه | Clogged drain line, excessive humidity | Clear drain line, ensure doors are closed, check ambient humidity. |
که چیرې د دې حلونو له هڅه کولو وروسته هم ستونزې دوام ومومي، نو د وړ خدماتو تخنیکین سره اړیکه ونیسئ.
7. مشخصات
The True Manufacturing GDM-49-HC~TSL01 is designed for commercial use, offering reliable refrigeration for various products.
| فیچر | تفصیل |
|---|---|
| برانډ | رښتیا |
| د ماډل معلومات | GDM-49-HC~TSL01 |
| د توکي وزن | ۲.۴۵ پونډه |
| د محصول ابعاد | 29.88 x 54.13 x 78.63 انچه |
| د لګولو ډول | فریسټینډینګ |
| د فارم فکتور | تړون |
| د رنګ اختیارونه | Black Standard, Optional White, Optional Stainless |
| Racks / Shelves | 8 د تار المارۍ |
| د ډیروسټ سیسټم | اتوماتیک |
| د دروازې زنګونه | د بیرته راګرځیدونکي |
| د دروازې د موادو ډول | شیشه |
| تصدیق | NSF |
| د دروازو شمیر | 2 |
| یخچال | R-290 |
Figure 3: Detailed specifications and plan view diagrams for the GDM-49-HC~TSL01.
8. تضمین او ملاتړ
True Manufacturing provides a comprehensive warranty for this product. For specific warranty terms and conditions, please refer to the warranty card included with your unit or visit the official True Manufacturing website. For technical support, parts, or service inquiries, please contact your authorized True dealer or True Manufacturing customer service directly. Ensure you have your model number (GDM-49-HC~TSL01) and serial number available when contacting support.
True Manufacturing Contact Information:
Webسایټ: www.truemfg.com
Phone: Refer to your product documentation for regional contact numbers.
