پیژندنه
This manual provides essential information for the safe and effective use of the ABB LTC Low Terminal Covers XT7 / XT7 M F 4P. These covers are designed for use with automatic switches in moulded boxes, specifically for fixed four-pole configurations. Please read this manual thoroughly before installation and operation.
د خوندیتوب معلومات
خبرداری: Electrical installation and maintenance should only be performed by qualified personnel. Failure to follow these instructions can result in serious injury or death.
- د وسیلې نصبولو یا خدمت کولو دمخه تل بریښنا قطع کړئ.
- ډاډ ترلاسه کړئ چې ټولې اړیکې خوندي دي او د ځایی بریښنایی کوډونو سره مطابقت لري.
- محصول مه کاروئ که چیرې دا زیانمن ښکاري.
- د ماشومانو د لاسرسي څخه لرې وساتئ.
د بسته محتويات
ډاډ ترلاسه کړئ چې ټول توکي په کڅوړه کې شتون لري:
- 2 x LTC Low Terminal Covers XT7 / XT7 M F 4P
- د لارښود لارښود (دا سند)
Image: Two ABB LTC Low Terminal Covers. The top cover is shown from a slightly elevated angle, revealing its flat top surface with embossed patterns and ribbed side. The bottom cover is inverted, showing the internal structure designed to house electrical terminals, also with ribbed sides. Both covers are dark grey.
تنظیم او نصب کول
These terminal covers are designed for specific ABB automatic switches in moulded boxes (XT7 / XT7 M F 4P series). Follow the instructions provided with your main automatic switch for proper installation.
- سویچ چمتو کړئ: Ensure the automatic switch is properly mounted and all power is disconnected.
- د ترمینلونو پیژندنه: Locate the low terminals on your XT7 / XT7 M F 4P automatic switch that require covering.
- د پوښ ځای ونیسئ: Align the LTC low terminal cover with the corresponding terminals. The cover is designed to fit snugly over the terminal connections.
- د پوښ خوندي کول: Gently press the cover into place until it clicks or is firmly seated. Ensure there are no gaps and the cover is securely attached.
- Repeat for all Terminals: Use the second cover for the remaining set of terminals if applicable.
- نصب کول تایید کړئ: Double-check that both covers are correctly installed and provide adequate protection for the terminals.
عملیاتي لارښوونې
The LTC Low Terminal Covers are passive components designed to provide protection for electrical terminals. They do not have active operational functions. Once installed, their purpose is to insulate and protect the low terminals of the automatic switch from accidental contact and environmental factors.
- Ensure covers remain securely in place during operation of the automatic switch.
- Do not attempt to remove covers while the switch is energized.
ساتنه
These terminal covers require minimal maintenance. Regular inspection is recommended to ensure their integrity and proper function.
- پاکول: If necessary, clean the covers with a dry, lint-free cloth. Do not use abrasive cleaners or solvents.
- معاینه: Periodically check for any signs of damage, cracks, or discoloration. Ensure they remain securely attached to the automatic switch.
- بدلول: If a cover is damaged or no longer fits securely, replace it immediately with an authentic ABB replacement part (Model: 1SDA107476R1).
د ستونزو حل کول
As passive protective components, troubleshooting for these terminal covers is limited. Most issues relate to improper installation or physical damage.
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| Cover does not fit or is loose. | Incorrect model of cover for the switch; improper alignment; damaged cover. | Ensure you have the correct XT7 / XT7 M F 4P covers. Re-align and press firmly. Inspect for damage and replace if necessary. |
| پوښ مات شوی یا درز شوی دی. | Physical impact or stress. | Replace the damaged cover immediately to maintain safety and protection. |
مشخصات
| صفت | تفصیل |
|---|---|
| د محصول حواله | ABB 1SDA107476R1 |
| د محصول کورنۍ | Automatic Switch in Molded Box Accessories |
| ډول | LTC Low Terminal Covers |
| مطابقت | XT7 / XT7 M F 4P Automatic Switches |
| مقدار | په هر پیک کې دوه ټوټې |
| ابعاد | Approximately 18 x 14 x 9 cm (for the package) |
| وزن | Approximately 676 g (for the package) |
| رنګ | Multicoloured (as per product listing, typically grey) |
تضمین او ملاتړ
For warranty information and technical support regarding your ABB LTC Low Terminal Covers, please refer to the documentation provided with your main ABB automatic switch or visit the official ABB website. Ensure you have your product reference number (1SDA107476R1) ready when contacting support.
د ABB رسمي Webسایټ: www.abb.com
