1. پیژندنه
The Flipsky Dual FSESC6.6 Plus is an advanced Electronic Speed Controller (ESC) designed for high-performance electric vehicles such as e-bikes, ESK8s, longboards, and DIY skateboarding projects. This manual provides essential information for the proper installation, configuration, and operation of your ESC.
2. د خوندیتوب معلومات
- د فرم ویئر مطابقت: It is recommended to keep firmware 5.2 from the factory. New firmware upgrades may damage the ESC.
- PCB Protection: Do not remove the shrink wrap. This protects the PCB electronic components from impurities or metals, which could result in short circuits or ESC damage.
- ډاډ ترلاسه کړئ چې ټولې اړیکې خوندي او په سمه توګه موصل شوي دي ترڅو د بریښنایی خطرونو مخه ونیول شي.
- Always wear appropriate safety gear when operating electric vehicles.
3. د بسته محتويات
ډاډ ترلاسه کړئ چې ټول توکي ستاسو په بسته کې شامل دي:
- 1x Dual FSESC6.7+Heatsink
- 2x ESC Sensor Wires
- 1x LED Button
- د 1x مایکرو USB کیبل
- 1x لارښود لارښود
د ان باکس کولو ویډیو
Video 3.1: This video demonstrates the unboxing process of a Flipsky ESC, showing how the components are packaged and removed from the box.
4. د محصول ب Featuresې
- Dual FSESC6.7 Plus (Pro switch) based on Dual FSESC6 with Power on/off by pressing the button.
- Changed the USB port soldering process to SMT soldering instead of manual soldering.
- Changed the big capacitors to SMT mounting capacitors, and added more MOSFETs on the bottom side.
- Added CAN bus connector, for more convenient 4WD setup.
5. مشخصات
| فیچر | تفصیل |
|---|---|
| د ماډل نوم | Flipsky Dual FSESC6.7 Plus with Anti-Spark Switch Integrated Based on VESC6 Electric 100A 12S ESC Speed Controller for Electric Skateboard |
| برخه شمیره | FSESC6.6 Plus |
| ابعاد (L x W x H) | ۷.۱۳ x ۳.۷ x ۲.۰۵ انچه (پیکج) |
| Size (including heatsink) | 81x77x20mm |
| وزن | 0.32 Kilograms (Package) |
| رنګ | Black+Yellow |
6. ترتیب او نصب کول
6.1 د تارونو نښلول
Follow these steps to correctly connect the ESC to your system components:
- Connect the motor phase wires (typically three thick wires) from the ESC to your motors.
- Connect the hall sensor wires (smaller multi-pin connector) from the ESC to your motors, if applicable.
- Connect the power switch button to the designated port on the ESC.
- Connect the battery wires (red for positive, black for negative) to the main power input of the ESC.
- Connect the remote receiver to the PPM or UART port on the ESC, depending on your remote type.
- Connect any optional accessories such as brake lights, front lights, or horn to their respective ports on the ESC.
Wiring Connection Video Guide
Video 6.1: This video provides a step-by-step guide on connecting the ESC to motors, hall sensors, battery, and other accessories.
6.2 VESC Tool Configuration
After physical connections, configure the ESC using the VESC Tool software:
- Connect the ESC to your computer via the Micro USB cable.
- Power on the ESC using the integrated button.
- Open the VESC Tool software on your computer.
- Click 'Connect' to establish communication between the VESC Tool and the ESC.
- Navigate to the 'Motor Setup' tab and set 'Motor Rated Current(A)', 'Li-ion Battery Series(S)', and 'Cell Cut-Off Voltage' according to your motor and battery specifications.
- Click the 'Identification Button' and confirm to proceed with motor parameter identification.
- Review the parameter identification results to ensure they are correct.
- Go to the 'Control Setup' tab and select the appropriate 'Input Signal Type' (e.g., UART for Flipsky remotes).
- Choose the desired 'UART Control Mode' and 'Extra Interface' options based on your setup (e.g., Current Gear Reverse Brake, Front/Brake Light and Horn).
- Click 'Write Setup' to save all configurations to the ESC.
VESC Tool Configuration Video Guide
Video 6.2: This video demonstrates the process of connecting the ESC to VESC Tool, identifying motor parameters, and configuring control settings.
7. عملیاتي لارښوونې
7.1 د ریموټ کنټرول عملیات
After successful VESC Tool configuration, you can operate your electric vehicle using a compatible remote control:
- Ensure the remote control is paired with the ESC. Confirm the 'Control type' is UART and 'ESC Type' is FTESC on the remote's display.
- Use the throttle gear to accelerate and brake. Pull down the throttle gear to activate the rear brake light.
- Short press the remote's power button once to turn the front lights on or off.
- Press the remote's power button twice quickly to activate or deactivate the horn.
Remote Control Demonstration
Video 7.1: This video demonstrates the basic functions of the remote control, including throttle, brake, and light/horn activation.
7.2 Riding Demonstration
Video 7.2: This video shows the ESC in action on an electric skateboard, demonstrating its performance and control during a ride.
8. ساتنه
- Regularly inspect all wiring connections for looseness or damage.
- Keep the ESC and surrounding components clean and free from dust, dirt, and moisture.
- Avoid exposing the ESC to extreme temperatures or direct sunlight for prolonged periods.
- Do not attempt to modify the ESC's hardware or remove the factory-installed shrink wrap.
9. ستونزه حل کول
- ESC not responding or locking up: Check all power and signal connections. Ensure the battery is adequately charged. If using a CAN bus setup, verify the CAN switch is correctly positioned.
- Motor not recognized by VESC Tool: Confirm the USB connection is secure and the ESC is powered on. Try restarting the VESC Tool and reconnecting.
- Unexpected behavior after firmware update: If you updated the firmware beyond version 5.2 and experience issues, it may be due to incompatibility. Contact Flipsky support for assistance.
- Intermittent connection with remote: Ensure the remote receiver is securely connected to the ESC and that the remote is fully charged and paired.
10. تضمین او ملاتړ
The Flipsky Dual FSESC6.6 Plus comes with a 2-month warranty.
For technical support, troubleshooting assistance, or warranty claims, please contact Flipsky customer service directly.
