د ZTW شارک G2 لړۍ 40A دوه اړخیزه د اوبو یخولو برش پرته ESC کارونکي لارښود

1. محصول ختم شوview

The ZTW Shark G2 Series 40A Bi-Direction Water Cooling Brushless ESC is designed for RC boat applications and other DIY projects requiring precise motor control. It features a robust design with water cooling for optimal performance and durability.

کلیدي ځانګړتیاوې:

• Bi-directional function (forward and backward).
• Aluminum water cooling system to reduce ESC heat.
• Soft start capability adaptable to different RPM and motor pole configurations.
• Over-temperature protection, low voltage cut-off protection, and signal loss protection.
• Strong BEC output: 4A/5.5V continuous, peak 8A.
• Supports high RPM motors and is programmable via LCD programming card and transmitter.
• High efficiency with low resistance and low heat MOSFET and 32-bit CPU.

غوښتنلیکونه:

• RC boat inrunner motors.
• Underwater thruster engines for RC bait tug boats, ROVs, and submarines.
• Various DIY projects requiring bi-directional motor control.

Figure 1: The ZTW Shark G2 40A Bi-Directional Electronic Speed Controller.

شکل 2: پایview of the ZTW Shark G2 ESC highlighting its new generation bi-directional capabilities and various applications.

Figure 3: The ZTW Shark G2 ESC, emphasizing its high-performance 32-bit CPU and stable, accurate throttle response.

2. مشخصات

۳. تنظیم او پروګرام کول

The ZTW Shark G2 ESC can be programmed using either your transmitter or an optional LCD programming card. This section details both methods.

3.1 Programming via Transmitter

Follow these steps to program your ESC using a transmitter:

1. ټرانسمیټر چالان کړئ.
2. Move the throttle stick to the top (maximum) position.
3. Connect a battery to the ESC. The ESC will emit a series of tones indicating the programming mode.
4. Listen to the tones and refer to the programming chart (typically provided with the ESC) to identify the desired parameter.
5. Once the tone for the desired parameter is heard, move the throttle stick to the bottom (minimum) position. This enters the corresponding parameter item.
6. The ESC will then emit tones corresponding to the available values for that parameter. Move the throttle stick to the top position when the tone for the desired value is heard. This saves the value.
7. Programming is complete for that parameter. Disconnect the battery to exit programming mode.

3.2 Programming via LCD Program Box

For more precise and visual programming, an optional LCD Program Box can be used. Connect the signal wire from the ESC to the program box, then power the ESC. The program box will display the current settings, allowing you to adjust them directly.

Figure 4: The ZTW Shark G2 ESC showing its various wiring connections for power, motor, and signal.

4. عملیاتي لارښوونې

4.1 Bi-Directional Function (SMR)

The ZTW Shark G2 ESC supports a Switch Motor Rotation (SMR) function, enabling bi-directional motor operation. This feature is particularly useful for applications requiring forward and reverse movement.

1. Ensure the SMR function is set to 'ON' in the ESC programming (refer to Section 3.1 or 3.2).
2. Plug the throttle and reverse signal wire into the receiver.
3. To change the motor rotation direction, flip the 2-stage switch on your transmitter.
4. یادونه: The SMR function is effective only when the throttle is below 50%.
5. مهم: The SMR function is intended for use when the aircraft (or RC vehicle) is landing on the ground. It can effectively shorten the landing distance. It is not recommended for in-flight or high-speed directional changes.

5. ساتنه

To ensure the longevity and optimal performance of your ZTW Shark G2 ESC, consider the following general maintenance guidelines:

• Regularly inspect all wiring and connectors for signs of wear, corrosion, or damage. Replace any compromised components immediately.
• Keep the ESC clean and free from dirt, dust, and debris. Use a soft, dry brush or compressed air for cleaning.
• Ensure the water cooling system is clear of obstructions and functioning correctly, especially after use in dirty or sandy water.
• ESC په یخ او وچ ځای کې د مستقیم لمر وړانګو او سختې تودوخې څخه لرې وساتئ.

Figure 5: The ZTW Shark G2 ESC positioned near water, demonstrating its water-cooling design. Regular inspection of the cooling system is recommended.

6. ستونزه حل کول

If you encounter issues with your ZTW Shark G2 ESC, consider the following common troubleshooting steps:

• ځواک نشته: Check battery connections, ensure the battery is charged, and verify all wiring is secure.
• موټر ځواب نه ورکوي: Confirm the ESC is properly connected to the receiver and motor. Recalibrate the throttle range if necessary. Check motor and ESC connections for continuity.
• موقتي عملیات: Inspect for loose connections, signal interference, or overheating. Ensure adequate ventilation for the ESC.
• Incorrect Motor Direction: Adjust the motor rotation setting in the ESC programming (refer to Section 4.1).
• ډیر ګرمول: Verify the water cooling system is functioning correctly and not obstructed. Ensure the ESC is not overloaded (e.g., using an undersized propeller or motor).

If problems persist after attempting these steps, contact ZTW customer support for further assistance.

7. د خوندیتوب معلومات

While specific safety information was not provided, it is crucial to observe general safety precautions when operating RC electronic components:

• Always handle LiPo batteries with care. Do not overcharge, over-discharge, or puncture them.
• ډاډ ترلاسه کړئ چې ټول بریښنایی اتصالونه خوندي او په سمه توګه موصل شوي دي ترڅو د لنډ سرکټ مخه ونیول شي.
• Operate RC equipment in open areas, away from people, animals, and obstacles.
• Keep hands and loose clothing away from rotating propellers or moving parts.
• Disconnect the battery from the ESC when not in use or during maintenance.
• Do not modify the ESC or its components, as this may void the warranty and create safety hazards.

8. تضمین او ملاتړ

For warranty information, technical support, or service inquiries regarding your ZTW Shark G2 Series 40A Bi-Direction Water Cooling Brushless ESC, please refer to the official ZTW webسایټ ته لاړ شئ یا خپل مجاز پلورونکي سره اړیکه ونیسئ. د تضمین ادعاوو لپاره د پیرود ثبوت په توګه د پیرود رسید وساتئ.