د جیکار ډیجیټیک QC1938 100MHz ډیجیټل اوسیلوسکوپ کارونکي لارښود

1. پیژندنه

This manual provides detailed instructions for the safe and effective operation of your Jaycar Digitech QC1938 100MHz Digital Oscilloscope. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance. Retain this manual for future reference.

2. د خوندیتوب معلومات

Observe the following safety precautions to prevent injury and avoid damage to the instrument or any products connected to it.

• د بریښنا سرچینه: Connect the oscilloscope only to the power source specified in this manual.
• ځمکني کول: ډاډ ترلاسه کړئ چې وسیله په سمه توګه په ځمکه کې ده ترڅو د بریښنا شاک مخه ونیول شي.
• تحقیقات: Use only probes supplied or recommended by the manufacturer. Ensure probes are rated for the voltage اندازه کیږي.
• وینټیلیشن: د هوا د بهېدو لارې مه بندوئ. د آلې شاوخوا د هوا مناسب جریان ډاډمن کړئ.
• چاپیریال: Operate the oscilloscope in a dry environment. Avoid exposure to moisture, dust, or extreme temperatures.
• خدمت کول: Refer all servicing to qualified service personnel. Do not attempt to repair the instrument yourself.

3. د بسته محتويات

ډاډ ترلاسه کړئ چې لاندې ټول لیست شوي توکي ستاسو په کڅوړه کې شتون لري:

• Jaycar Digitech QC1938 Digital Oscilloscope
• 10:1 Passive Probe with 1.5m lead
• 2 x BNC to Clip Test Leads
• USB کیبل
• د بریښنا لیډ
• د کارونکي لارښود (دا لاسوند)

4. محصول ختم شوview

The Jaycar Digitech QC1938 is a 100MHz Digital Oscilloscope designed for precise electronic measurements. It features a 7-inch color LCD screen, two independent channels, and a built-in waveform generator.

کلیدي ځانګړتیاوې:

• 7-inch TFT color LCD screen with 800 x 480 pixel resolution
• Two independent input channels
• 100MHz bandwidth and 1GSa/s sampد نرخ کچه
• 8M memory depth (single channel)
• Integrated 25MHz waveform generator (Sine, Square, Ramp, Exponential, Noise, DC)
• Auto scale function for automatic sine and square wave detection
• 14 trigger modes including Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, and IIC
• 5 serial protocol triggers and decodes: RS232/UART, I2C, SPI, CAN, and LIN
• Two 3-digit digital voltmeters and a 6-digit hardware frequency indicator
• 32 types of auto measurements with real-time statistics
• USB Host/Device interface for computer control and data storage

5. ترتیب کول

5.1 د بریښنا نښلول

1. Connect the supplied power lead to the power input on the rear panel of the oscilloscope.
2. Plug the other end of the power lead into a grounded AC power outlet.
3. Press the power button on the front panel to turn on the oscilloscope.

5.2 د پلټنې اتصال

1. Connect the BNC connector of the passive probe to either Channel 1 (CH1) or Channel 2 (CH2) input on the front panel.
2. Attach the ground clip of the probe to the circuit's ground point.
3. Connect the probe tip to the test point in your circuit.
4. Ensure the probe's attenuation setting (e.g., 1X or 10X) matches the setting on the oscilloscope for accurate readings.

6. عملیاتي لارښوونې

6.1 بنسټیز عملیات

• Auto Scale: Press the 'AUTO SET' button to automatically adjust vertical, horizontal, and trigger settings for a stable waveform display. This function detects sine and square waves automatically.
• Vertical Controls (VOLTS/DIV, POSITION): Use the VOLTS/DIV knobs to adjust the vertical scale (voltage per division) for each channel. The POSITION knobs shift the waveform vertically.
• Horizontal Controls (SEC/DIV, POSITION): Use the SEC/DIV knob to adjust the horizontal scale (time per division). The horizontal POSITION knob shifts the waveform horizontally.
• د محرک کچه: Adjust the 'TRIGGER LEVEL' knob to set the voltage level at which the oscilloscope captures a waveform.

6.2 پرمختللې دندې

• د څپو جنریټر: Access the waveform generator menu to select and configure output waveforms such as Sine, Square, Ramp, Exponential, Noise, and DC. Connect the 'WAVE GEN' output to your circuit.
• د محرک حالتونه: Utilize the 14 available trigger modes (Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC) to capture specific events. Select modes via the 'TRIGGER' menu.
• Serial Protocol Decoding: The oscilloscope supports decoding for RS232/UART, I2C, SPI, CAN, and LIN protocols. Configure these settings in the 'DECODE' menu to view decoded data.
• اندازه کول: The device offers 32 types of automatic measurements with real-time statistics (maximum, minimum, standard deviation, etc.). Access these via the 'MEASURE' menu.
• د USB نښلول: Connect a USB thumb drive to the USB Host port to save oscilloscope setups, waveforms, reference waveforms, CSV files, and images. The USB Device port allows for remote control from a computer using SCPI commands.

7. ساتنه

7.1 پاکول

د وسیلې د پاکولو لپاره، نرم ټوکر وکاروئampened with a mild detergent solution. Do not use abrasive cleaners or solvents that could damage the casing یا سکرین. ډاډ ترلاسه کړئ چې وسیله بنده ده او د پاکولو دمخه یې پلګ خلاص شوی دی.

7.2 ذخیره کول

When not in use, store the oscilloscope in a dry, dust-free environment away from direct sunlight and extreme temperatures. Use the original packaging or a suitable case for protection during transport.

8. ستونزه حل کول

If you encounter issues with your oscilloscope, refer to the following common problems and solutions:

که چیرې د دې حل لارو هڅه کولو وروسته هم ستونزه دوام ومومي، مهرباني وکړئ د پیرودونکو ملاتړ سره اړیکه ونیسئ.

9. مشخصات

10. تضمین او ملاتړ

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for warranty claims.