1. پیژندنه
This manual provides essential information for the proper setup, operation, and maintenance of your LDARC X-BOSS FM900 2.4GHz FASST Receiver. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2. محصول ختم شوview
Image: The LDARC X-BOSS FM900 receiver, a compact circuit board featuring surface-mount components, an integrated antenna, and clearly labeled 'FM900' branding. This image illustrates the physical design and component layout of the receiver.
3. ځانګړتیاوې
- Offers great reliability, stable signal link, precision antenna, and high sensitivity.
- Compact and lightweight design for various applications.
- Integrated LNA (Low Noise Amplifier) for enhanced signal reception.
- RSSI (Received Signal Strength Indicator) output for real-time signal monitoring.
4. مشخصات
| مشخصات | تفصیل |
|---|---|
| توکي | FM900 Receiver |
| وزن | 1.2 ګرامه |
| ابعاد | 11.5mm x 21mm |
| والیtage | 4-6V |
| کاري سلسله | >900m (air distance without electromagnetic interference) |
| پروتوکول | FASST |
| محصول 1 | LNA |
| محصول 2 | RSSI |
| ملاتړ شوي لیږدونکي | T8FG, T14SG, T16SZ, T18SZ, T18MZ, T32MZ TX |
| Real-Time RSSI Compatibility | F3, F4, F7, etc. flight controllers |
5. د بسته محتويات
- 1x LDARC X-BOSS FM900 Receiver
6. ترتیب کول
6.1. نصب کول
Carefully connect the receiver to your flight controller or power source, ensuring correct polarity and signal connections. Mount the receiver securely in your model, away from sources of electrical interference. Position the antenna for optimal signal reception, avoiding obstructions.
6.2. Binding Procedure
To establish communication between your transmitter and the FM900 receiver, follow these general binding steps:
- Power on your transmitter and select the FASST protocol.
- Place your transmitter in binding mode (refer to your transmitter's manual for specific instructions).
- Apply power to the FM900 receiver. The receiver's LED indicator should begin to flash, indicating it is ready for binding.
- Once the binding process is complete, the receiver's LED will typically turn solid green, indicating a successful connection.
- Power cycle both the transmitter and receiver to confirm the binding is retained.
7. عملیاتي لارښوونې
After successful binding and installation, ensure your transmitter and receiver are powered on before operating your model. Always perform a range check and verify all control surfaces respond correctly before flight. Monitor the RSSI output on your flight controller or OSD (On-Screen Display) to ensure a strong signal link during operation.
8. ساتنه
- رسیور پاک او له دوړو، خاورې او رطوبت څخه پاک وساتئ.
- Regularly inspect antenna connections for damage or loose contacts.
- د اوږدې مودې لپاره د لوړ حرارت یا مستقیم لمر وړانګو سره د رسیدونکي د افشا کولو څخه ډډه وکړئ.
- Ensure proper ventilation around the receiver during operation.
9. ستونزه حل کول
- No Signal/Loss of Link: Re-check binding procedure. Ensure transmitter and receiver are powered on. Verify antenna connection and placement. Check for potential interference sources.
- وقفه ای سیګنال: Inspect antenna for damage. Ensure receiver is not too close to high-current wires or other electronic components that may cause interference.
- ریسیور نه فعالیږي: د بریښنا پیوستون او حجم تایید کړئtage supply (4-6V). Check for shorts or incorrect wiring.
- د کنټرول ناسم ځواب: Confirm correct channel mapping in your flight controller or model setup. Re-bind the receiver if necessary.
۷. د تضمین او ملاتړ معلومات
LDARC products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please reach out to your authorized LDARC dealer or visit the official LDARC webد مرستې لپاره سایټ.
