1. پیژندنه
The Datakom D-300-MK2 is a cost-effective, modular genset controller designed for internet monitoring through plug-in modules. It functions as an AMF (Automatic Mains Failure) unit, ATS (Automatic Transfer Switch) unit, remote start controller, manual start controller, and engine controller. This manual provides essential information for the proper installation, operation, and maintenance of the D-300-MK2 controller.
شکل 1.1: مخکی view of the D-300-MK2 controller, highlighting its features and functionalities.
2. Key Features and Functionalities
The D-300-MK2 controller offers a wide range of features and functionalities for comprehensive genset management:
2.1. عمومي ځانګړتیاوې
- Diesel and gas genset support
- 400Hz operation support
- 400 event logs, full snapshot
- All parameters front panel editable
- 3-level configuration password
- 128x64 graphical LCD display
- Downloadable languages
- Waveform display of V & I
- Harmonic analysis of V & I
- 16Amp MCB & GCB outputs
- 8 configurable digital inputs
- 6 configurable digital outputs
- 2 configurable analog inputs
- Both CANBUS-J1939 & MPU
- 3 configurable service alarms
- Multiple automatic exercise
- Weekly operation schedule
- Dual mutual standby with equal aging of gensets
- Manual "speed fine adjust" on selected ECUs
- Automatic fuel pump control
- Disable protections feature
- Excess power protection
- د بریښنا محافظت بیرته
- Overload IDMT protection
- Load shedding, dummy load
- Multiple load management
- Current unbalance protection
- والیtage unbalance protection
- Fuel filling & fuel theft alarm
2.2. پرمختللي ځانګړتیاوې
- Battery back-up real time clock
- Idle speed control
- Battery charge run enabled
- Contactor mode support
- Multiple nominal conditions
- Contactor & MCB drive
- 4 quadrant genset power counters
- Mains power counters
- Fuel filling counter
- Fuel consumption counter
- Modem diagnostics display
- Configurable through USB, RS-232 and GPRS
- Free configuration program
- Allows SMS controls
- Ready for central monitoring
- Mobile genset support
- Automatic GSM geo-location
- GPS connectivity (RS232)
- Easy USB firmware upgrade
- Free rating with external gasket
2.3. فعالیت
- AMF unit
- د ATS واحد
- Manual start controller
- Engine controller
- Remote display panel
3. محصول ختم شوview and Plug-in Modules
The D-300-MK2 controller features a robust design with various connection points and supports modular extensions for enhanced communication capabilities.
شکل 3.1: Detailed back panel view of the D-300-MK2 controller, showing all terminal connections and module slots.
3.1. Plug-in Communication Modules
The D-300-MK2 supports various plug-in modules to extend its communication capabilities, allowing for internet monitoring and remote control.
- GSM Modem (2G-3G-4G): For cellular communication and SMS controls.
- Ethernet (10/100Mbps): د تار لرونکي شبکې اتصال لپاره.
- Wi-Fi (802.11 b/n): د بېسیم شبکې اتصال لپاره.
- RS-485 (2400-57600baud): For industrial communication protocols.
- RS-232 (2400-57600baud): For serial communication, including GPS connectivity.
شکل 3.2: Illustration of various plug-in modules available for the D-300-MK2 controller, including GSM Modem, RS-485, Ethernet, RS-232, and Wi-Fi.
4. تخنیکي مشخصات
د تخنیکي مشخصاتو پوهیدل د سم نصب او عملیاتو لپاره خورا مهم دي.
- بدیل والیمtage: 0 to 300 V-AC (Ph-N)
- Alternator frequency: 0-650 Hz
- مینز ولtage: 0 to 300 V-AC (Ph-N)
- د اصلي فریکونسي: 0-650 Hz
- توپولوژي: 1-2-3 phase, with or without neutral
- DC Supply Range: 8.0 to 36.0 V-DC.
- VA-cos accuracy: 0.5% + 1 عدد
- kVA-kW-kVAr accuracy: 1.0% + 1 عدد
- اوسنی مصرف: 80 mA DC max @ 12V-DC
- اوسني معلومات: current transformers, ../5A or ../1A.
- ډیجیټل معلومات: د ننوتلو حجمtage 0 to 36 V-DC.
- د انلاګ ان پټ سلسله: 0-5000 ohms
- Mains and genset contactor outputs: 16Amps@250V
- د DC محصولات: Protected mosfet semiconductor outputs, rated 1Amp@28V DC.
- Cranking dropouts: survives 0V for 100ms.
- Magnetic pickup voltage: 0.5 to 50V-AC.
- Magnetic pickup frequency: له 0 څخه تر 10000،XNUMX Hz پورې.
- Charge Alternator Excitation: 2W.
- د ښودلو سکرین: 2.9", 128x64 pixels
- د USB وسیله: USB 2.0 بشپړ سرعت
- د حرارت درجه: -20°C to 70°C (-4 to +158°F)
- د ذخیره کولو حرارت: -40°C to 80°C (-40 to +176°F)
- اعظمي رطوبت: 95٪ غیر کنډیشن.
- د IP محافظت: IP65 from front panel, IP30 from the rear (with gasket)
- ابعاد: 180 x 140 x 46 ملي میتر (WxHxD)
- Panel Cut-out Dimensions: 151 x 111 mm minimum.
- وزن: 300 ګرامه (نږدې)
- د قضیې مواد: High temperature, non-flammable ABS/PC
- لګول: Flat surface mounting on a Type 1 enclosure. Rear retaining plastic brackets.
5. نصب او ویرینګ
Correct installation and wiring are critical for the safe and reliable operation of the D-300-MK2 controller. Refer to the wiring diagram for detailed connections.
5.1. Typical Connections
The diagram below illustrates the typical wiring for the D-300-MK2, including connections for the alternator, mains, and engine control.
شکل 5.1: Typical wiring diagram for the D-300-MK2 controller, showing connections to alternator, mains, and engine components. Ensure all connections are made according to local electrical codes and safety standards.
- د بیټرۍ اړیکې: Connect BAT+ and BAT- terminals to the battery. Ensure battery negative is grounded.
- Alternator Connections: Connect alternator phases (L1, L2, L3, N) to the designated terminals.
- Mains Connections: Connect mains phases (L1, L2, L3, N) to the designated terminals.
- د انجن کنټرول: Connect starter motor, fuel solenoid, and other engine sensors (oil pressure, water temp, etc.) as per the diagram.
- MPU/J1939: Connect MPU (Magnetic Pickup Unit) or J1939 CANBUS for engine speed and data.
- فیوزونه: Install appropriate fuses for all power lines as indicated in the diagram.
- ځمکني کول: Ensure proper grounding for all components.
6. عملیات
The D-300-MK2 offers various operating modes to suit different genset applications.
6.1. د کنټرول طریقې
- لاسي پیل: Allows the user to manually start and stop the genset using the front panel buttons.
- ریموټ پیل: Enables starting and stopping the genset via a remote signal.
- Automatic Mains Failure (AMF): The controller automatically starts the genset upon detecting a mains power failure and transfers the load. It stops the genset and transfers the load back to mains when mains power is restored.
- Automatic Transfer Switch (ATS): Manages the transfer of load between mains and genset power sources.
6.2. څارنه او ارتباط
The D-300-MK2 provides extensive monitoring capabilities and supports various communication methods for remote access and data logging.
شکل 6.1: Communication diagram illustrating how the D-300-MK2 connects to various systems for monitoring and control, including GSM, Wi-Fi, Ethernet, RS-485, J1939, and USB.
- سیمه ییزه څارنه: The 128x64 graphical LCD display provides real-time data, alarms, and event logs.
- د USB نښلول: For local configuration and firmware updates using a PC.
- ریموټ څارنه: Through plug-in modules (GSM, Ethernet, Wi-Fi, RS-485, RS-232), the controller can communicate with central monitoring systems, HMI displays, and smartphones.
- J1939/MPU: Supports communication with electronic engines for engine data.
شکل 6.2: شاته پینل view alongside screenshots of the Scopemeter & Harmonics display, Rainbow Plus Program, Rainbow SCADA Central Monitoring, and Smartphone Support, demonstrating the comprehensive monitoring capabilities.
۲. د سافټویر ملاتړ
- Rainbow Plus Program: A free PC software for configuration, monitoring, and diagnostics.
- Rainbow SCADA Central Monitoring: For advanced remote monitoring and control of multiple gensets.
- Smartphone Support: Allows monitoring and control via a dedicated smartphone application.
7. ساتنه
Regular maintenance ensures the longevity and reliable operation of your D-300-MK2 controller and the genset it manages.
- پاکول: Keep the controller's front panel clean and free from dust. Use a soft, dry cloth. Avoid abrasive cleaners or solvents.
- د اړیکو چک: Periodically inspect all wiring connections for tightness and corrosion. Loose connections can lead to intermittent operation or damage.
- د فرم ویئر تازه معلومات: جوړونکي وګورئ website for available firmware updates to ensure optimal performance and access to new features. Updates can typically be performed via the USB port.
- د بیټرۍ معاینه: Ensure the genset's battery, which powers the controller, is in good condition and properly charged.
- د چاپیریال شرایط: ډاډ ترلاسه کړئ چې عملیاتي چاپیریال د زیان مخنیوي لپاره د ټاکل شوي تودوخې او رطوبت حدودو کې پاتې کیږي.
8. ستونزه حل کول
This section provides general guidance for common issues. For complex problems, consult a qualified technician or Datakom support.
- کنټرولر نه فعالیږي:
- د بیټرۍ پیوستون او حجم چیک کړئtage.
- Verify fuses are intact.
- Genset Not Starting:
- Check fuel level and battery charge.
- Inspect engine fault codes on the controller display.
- Verify all safety shutdowns are clear.
- د اړیکو مسایل:
- Ensure plug-in modules are correctly installed.
- Check network cables (Ethernet) or Wi-Fi signal strength.
- Verify SIM card (GSM) is active and has credit.
- Confirm correct IP addresses and port settings in software.
- ناسم لوستل:
- Check sensor connections and calibration.
- Verify CT (Current Transformer) ratios are correctly configured.
9. موافقت
The D-300-MK2 controller complies with relevant international standards and directives.
- د EU لارښوونو سره مطابقت:
- 2014/35/EC (ټيټ والیtage)
- 2014/30/EC (electro-magnetic compatibility)
- د حوالې معیارونه:
- EN 61010 (د خوندیتوب اړتیاوې)
- EN 61326 (EMC اړتیاوې)
- UL & CSA Compatibility:
- -UL 6200, Controls for Stationary Engine Driven Assemblies (Certificate #: 20140725-E314374)
- -CAN/CSA C22.2 No. 14-13 - Industrial Control Equipment
10. د ملاتړ او اړیکو معلومات
For further assistance, technical support, or inquiries, please contact Datakom Electronics Limited:
- ټیلیفون: +90-216 466 84 60
- فکس: +90-216 364 65 65
- برېښناليک: datakom@datakom.com.tr
- Webسایټ: http://www.datakom.com.tr
