1. پیژندنه
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your KATOOL KT-B750 Wheel Balancer. Please read this manual thoroughly before operating the machine to ensure proper usage and to prevent damage or injury. Keep this manual for future reference.
2. د خوندیتوب معلومات
Always adhere to the following safety guidelines when operating the KATOOL KT-B750 Wheel Balancer:
- Ensure the machine is placed on a level, stable surface.
- Connect the machine to a properly grounded power outlet (110V).
- مناسب شخصي محافظتي تجهیزات (PPE) واغوندئ، په شمول د خوندیتوب عینکې او دستکشې.
- لاسونه، ویښتان، او نرمې جامې د حرکت کولو برخو څخه لرې وساتئ.
- که چیرې کومې برخې زیانمنې یا ورکې وي، ماشین مه چلوئ.
- Ensure the wheel guard is properly positioned before starting the balancing process.
- یوازې روزل شوي پرسونل باید دا تجهیزات وکاروي او وساتي.
- د هر ډول ساتنې یا سمون ترسره کولو دمخه بریښنا قطع کړئ.
3. د بسته محتويات
د خلاصولو پر مهال، ډاډ ترلاسه کړئ چې ټولې برخې شتون لري:
- KATOOL KT-B750 Wheel Balancer Unit
- د څرخ ساتونکی
- Automatic Measurement Ruler
- Standard accessories for wheel mounting (e.g., cones, quick-release nut)
- د لارښود لارښود (دا سند)
4. ترتیب کول
- بسته بندي کول: Carefully remove the wheel balancer from its packaging. Inspect for any shipping damage.
- ځای په ځای کول: Position the machine on a firm, level concrete floor capable of supporting its weight and the weight of the wheels being balanced. Ensure adequate clearance around the machine for safe operation and maintenance.
- مجلس:
- Attach the wheel guard to the designated mounting points. Ensure it can move freely and securely cover the wheel during operation.
- Connect the automatic measurement ruler if it is not pre-installed.
- د بریښنا پیوستون: Connect the power cord to the machine and then to a dedicated 110V, grounded electrical outlet.
- ابتدايي اندازه کول: Refer to the on-screen prompts or a dedicated section in the full manual for initial calibration procedures, which may include spindle calibration and weight tray calibration.
5. عملیاتي لارښوونې
Follow these steps for balancing a wheel:
- څرخ پورته کړئ: Securely mount the wheel onto the balancer's spindle using the appropriate cone and quick-release nut. Ensure the wheel is centered and tightened properly.
- Input Wheel Data:
- Use the automatic measurement ruler to measure the wheel's distance (A) and diameter (D). The machine will automatically input these values.
- Manually input the wheel's width (W) using the control panel.
- Select the desired balancing mode (e.g., static, dynamic, alloy wheel modes).
- Lower Wheel Guard: Close the wheel guard completely. The machine will not operate if the guard is open.
- Start Balancing Cycle: Press the START button on the control panel. The wheel will spin, and the machine will measure the imbalance.
- پایلې ولولئ: Once the spin cycle completes, the display will show the required weight amounts and their precise locations for correction.
- وزنونه تطبیق کړئ: Open the wheel guard, apply the indicated balance weights to the inner and outer planes of the rim as shown on the display.
- Re-spin (Verification): Close the wheel guard and press START again to verify the balance. The display should show zero or minimal imbalance. Repeat the process if necessary until the wheel is balanced.
- څرخ لرې کړئ: Once balanced, open the wheel guard and carefully remove the wheel from the spindle.
6. ساتنه
Regular maintenance ensures the longevity and accuracy of your KATOOL KT-B750 Wheel Balancer:
- پاکول: Keep the machine clean, especially the spindle, control panel, and measurement ruler. Use a soft, dry cloth. Avoid abrasive cleaners or solvents.
- سپینډل غوړول: Periodically apply a light lubricant to the spindle threads to ensure smooth operation of the quick-release nut.
- د کیلیبریشن چک: Perform a calibration check regularly (e.g., monthly or after significant use) to maintain accuracy. Refer to the machine's specific calibration procedure.
- د کیبل معاینه: Inspect all power cords and cables for signs of wear or damage. Replace damaged cables immediately.
- د څرخ ساتونکی: Ensure the wheel guard operates smoothly and securely. Clean any debris that might hinder its movement.
7. ستونزه حل کول
This section addresses common issues. For problems not listed, contact KATOOL customer support.
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| ماشین نه چالانېږي. | No power supply; faulty power cord; internal fuse blown. | Check power connection and outlet. Inspect power cord. Consult a qualified technician for fuse replacement. |
| څرخ نه ګرځي. | Wheel guard open; emergency stop engaged; motor issue. | Ensure wheel guard is closed. Check emergency stop button. Contact support if motor is unresponsive. |
| د توازن ناسمې پایلې. | د څرخ ناسم نصب؛ د معلوماتو ناسم داخلول؛ ماشین له اندازې بهر دی. | Re-mount wheel securely. Verify A, D, W values. Perform calibration procedure. |
| Automatic ruler not functioning. | Sensor obstruction; cable disconnection; ruler damage. | Clear any obstructions. Check cable connections. Contact support for repair. |
8. مشخصات
- ماډل: KT-B750
- نښه: KATOOL
- د بریښنا رسول: 110V
- Maximum Wheel Weight: ۱۱.۵۷ پونډه (۵.۲۵ کیلو ګرامه)
- د رم قطر: ۱۲.۶" - ۳۸.۲"
- د رم پلنوالی: ۱۲.۶" - ۳۸.۲"
- اندازه کول: Automatic measurement ruler for A and D values
- د لومړي شتون نیټه: د اپریل 17، 2024
9. تضمین او ملاتړ
For warranty information and technical support, please contact KATOOL directly. Keep your purchase receipt as proof of purchase. Details regarding specific warranty periods and terms are typically provided at the point of sale or on the manufacturer's official webسایټ
For assistance, please refer to the contact information provided by KATOOL or your authorized dealer.
