پیژندنه
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Total Automatic Self-priming Jet Pump, model TWP415006. Please read this manual thoroughly before operating the pump to ensure proper use and to prevent damage or injury.
د خوندیتوب لارښوونې
د اور، بریښنا شاک، یا ټپي کیدو خطر کمولو لپاره تل لاندې خوندیتوب احتیاطي تدابیر په پام کې ونیسئ:
- بریښنایی خوندیتوب: ډاډ ترلاسه کړئ چې د بریښنا رسولو د پمپ حجم سره سمون لريtage (220-240V~50Hz). Always connect the pump to a properly grounded outlet. Do not operate the pump with a damaged cord or plug.
- د اوبو خوندیتوب: Do not pump flammable or corrosive liquids. Ensure the pump is not submerged unless specifically designed for submersible use. Protect the pump from freezing temperatures.
- لګول: Install the pump in a dry, well-ventilated area, protected from direct sunlight and rain. Ensure stable mounting to prevent vibration.
- ساتنه: Disconnect power before performing any maintenance or repairs. Only qualified personnel should perform repairs.
- ماشومان او څاروي: د کار کولو پرمهال ماشومان او څاروي له پمپ څخه لرې وساتئ.
محصول پای ته ورسیدview او اجزا
The Total Automatic Self-priming Jet Pump TWP415006 is designed for efficient water transfer. It includes a 24L cylindrical tank, pressure switch, pressure gauge, stainless steel hose, and brass 3-way connector.

شکل 1: پایview of the Total Automatic Self-priming Jet Pump TWP415006.

Figure 2: Key features of the pump, including 1500W power, 24L tank, and copper wire motor.
شاملې برخې:
- 1 x Automatic Self-priming Jet Pump (1.5kW)
- 1 x 24L Cylindrical Tank
- 1 x د فشار سویچ
- 1 x Stainless Steel Hose
- 1 x د فشار ګیج
- 1 x Brass 3-way Connector
مشخصات
| پیرامیټر | ارزښت |
|---|---|
| ماډل | TWP415006 |
| والیtage | 220-240V ~ 50Hz |
| درجه بندي ځواک | 1500W (2.0HP) |
| اعظمي روانی | ۵،۵ لیتره/ دقیقه |
| Max. سر | 60m |
| Max. Suction | 9m |
| د پایپ قطر | ۶.۹" x ۳.۴" |
| د موټرو ډول | Copper Wire Motor |
| د امپیلر موادو | سټینلیس سټیل |
| د پمپ بدن | الکتروفورسیس |
| د شافټ مواد | Stainless Steel Welding (304+45#) |
| د کیبل اوږدوالی | 0.3m |
| د توکي وزن | 32 کیلوګرامه |
| د کڅوړې ابعاد | 62.7 x 57.3 x 36 سانتي متره |
چمتو کول
1. ځای پرځای کول
- Choose a flat, stable, and dry location for the pump, protected from direct weather exposure.
- Ensure adequate ventilation around the pump.
- پمپ د اوبو سرچینې ته د امکان تر حده نږدې ځای په ځای کړئ ترڅو د سکشن پورته کول کم کړئ.
2. د پایپ پیوستون
- د سکشن پایپ: Connect a rigid pipe of 1" diameter to the suction inlet. Ensure the suction pipe is airtight to prevent air leaks, which can affect priming and pump performance. Install a foot valve with a strainer at the end of the suction pipe in the water source to prevent debris from entering the pump and to maintain prime.
- د خارجولو پایپ: Connect a 1" diameter pipe to the discharge outlet. The included stainless steel hose and brass 3-way connector should be used for the pressure tank and pressure gauge connection.
- Use thread sealant tape on all threaded connections to ensure a watertight seal.
3. بریښنایی پیوستون
- Ensure the power supply is 220-240V~50Hz.
- Connect the pump to a dedicated, properly grounded electrical outlet.
- Do not use extension cords unless absolutely necessary, and if so, ensure they are rated for outdoor use and the pump's power requirements.
۱. د پمپ پریمینګ کول
- Before first use, or if the pump has run dry, it must be primed.
- Locate the priming plug on the top of the pump casing.
- Remove the priming plug and slowly fill the pump casing with clean water until it overflows.
- Replace the priming plug securely.
- Ensure the discharge valve is open before starting the pump.
عملیاتي لارښوونې
1. د پمپ پیل کول
- Ensure the pump is properly primed (see Setup section).
- ډاډ ترلاسه کړئ چې ټولې اړیکې خوندي او له لیک څخه پاک دي.
- Plug the pump into the grounded electrical outlet. The pump will start automatically when pressure drops below the set point of the pressure switch.
2. Monitoring Operation
- Observe the pressure gauge to ensure the system is operating within expected pressure ranges.
- د غیر معمولي غږونو یا وایبریشنونو لپاره غوږ ونیسئ، کوم چې ممکن ستونزه په ګوته کړي.
- Check for any leaks around connections.
3. بندول
- To stop the pump, simply unplug it from the power source. The automatic pressure switch will also stop the pump when the desired pressure is reached.
- For extended periods of non-use, especially in freezing conditions, drain the pump and pipes completely to prevent damage.
ساتنه
۵. منظمې معاینې
- Periodically inspect the pump and all connections for signs of wear, damage, or leaks.
- Check the pressure tank's air charge annually. Refer to the tank's specific instructions for proper air pressure.
- Ensure the foot valve strainer is clear of debris.
2. پاکول
- Keep the pump exterior clean and free of dust and dirt to ensure proper cooling.
- سخت کیمیاوي توکي او کثافات پاکونکي مه کاروئ.
۷.۳. د ژمي موسم (د سړې هوا لپاره)
- If the pump is installed in an area subject to freezing temperatures, it must be drained completely to prevent damage from ice expansion.
- Disconnect power, open all drain plugs, and remove the priming plug to allow all water to escape.
- Store the pump in a warm, dry place if possible.
د ستونزو حل کول
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| پمپ پیل نه کوي | No power; tripped circuit breaker; faulty motor. | Check power connection and circuit breaker. Consult a qualified electrician if motor is suspected faulty. |
| پمپ چلېږي خو اوبه نه بهېږي | Pump not primed; air leak in suction line; clogged foot valve/strainer; low water level in source. | Re-prime the pump. Check all suction connections for leaks. Clean foot valve strainer. Ensure adequate water in source. |
| ټیټ فشار یا جریان | Partial air leak; clogged impeller; worn components; incorrect pipe size. | Check suction line for small leaks. Inspect and clean impeller. Consult service for worn parts. Ensure correct pipe diameter. |
| ډیر ځله د پمپ چکرونه | د ټانک د فشار هوا چارج ډېر ټیټ دی؛ په سیسټم کې لیک؛ د فشار سویچ خراب دی. | Check and adjust pressure tank air charge. Inspect entire system for leaks. Test or replace pressure switch. |
| ډیر شور / وایبریشن | Cavitation (air in pump); loose mounting; bearing wear. | Ensure pump is primed and no air leaks. Secure pump mounting. Consult service for bearing issues. |
تضمین او ملاتړ
TOTAL products are manufactured to high-quality standards and are guaranteed against manufacturing defects. For warranty claims or technical support, please contact your local TOTAL authorized service center or the retailer from whom you purchased the product. Please retain your proof of purchase for warranty validation.
د نورو مرستو لپاره، تاسو کولی شئ لیدنه وکړئ TOTAL Store on Amazon.





