منځپانګې پټول
1 ډیجیلاګ ESP32 سوپر مینی دیو بورډ
2 مشخصات
3 ترتیب-1
4 ترتیب-1
5 ترتیب-2
6 اسناد / سرچینې
6.1 حوالې

Digilog-logo

ډیجیلاګ ESP32 سوپر مینی دیو بورډ

Digilog-ESP32-Super-Mini-Dev-Board-product

مشخصات

  • د محصول نوم: ESP32 سوپر مینی ډیو بورډ
  • د بورډ ډول: ESP32C3 Dev ماډل
  • اړیکه: USB CDC
  • د بوډ نرخ: 9600
  • په بورډ کې LED: GPIO8

ترتیب-1

My ESP32 Super Mini Dev Board (Fig. 1) accepts sketches from a PC, but it does not communicate with the Serial Monitor (Bd = 9600) though the onBoard LED (at GPIO8) blinks.
[image|403×203](upload://pRi2u3tDsAxTivzokiEplEtzhlC.jpeg)
شکل-1

Digilog-ESP32-Super-Mini-Dev-Board-fig-1

ترتیب-1

  • Board: “ESP32C3 Dev Module”
  • USB CDC on Boot: “Enabled”
  • Port: “COM13 (ESP32S3 Dev Module)” //no other option

سکیچ

  • define LED_BUILTIN 8
  • char myData[10];
  • باطل تنظیم ()
  • لړۍ پیل (9600);
  • pinMode(LED_BUILTIN, OUTPUT)
  • باطل لوپ()
  • ډیجیټل رایټ (LED_BUILTIN، لوړ)؛ // LED چالان کړئ (لوړ حجم دی)tage کچه)
  • delay(1000); // wait for a second
  • ډیجیټل رایټ (LED_BUILTIN، LOW)؛ // د حجم په جوړولو سره LED بند کړئtage LOW delay(1000)
  • بایټ n = سریال. شتون لري();
  • if (n != 0) { byte m = Serial.readBytesUntil(‘\n’, myData, sizeof (myData)-1); myData[m] = ‘\0’
  • Serial.println(myData); }
  • Serial.println(“Hello”); }

The following setup has solved the problem.

ترتیب-2

  • Board: “LOLIN C3 Mini”
  • USB CDC on Boot: “Enabled”
  • Port: “COM13 (ESP32S3 Dev Module)”
  • Bd = 9600

محصول

  • سلام
  • سلام
  • Arduino //From InputBox of SM to ESP32C3 to OutputBox of SM
  • سلام
  • سلام

Would be glad to hear your opinion as to — “what is LOLIN C3”.

  1. Do not place the ESP32C3 Super Mini Board on the Breadboard to avoid contact problems.
  2. په بورډ کې LED په DPin-8 کې وصل دی.
  3. Use a male-female jumper and connect the female side at DPin-9 to act as an external switch/button.
  4. The connection diagram of the onFig. 1 LED and a button are similar to Fig. 1.Digilog-ESP32-Super-Mini-Dev-Board-fig-2
  5. Select Board as follows: IDE 2.3.1 –> Tools –> ESP32.
  6.  LOLIN C3 Mini USB CDC On Boot: Enabled.
  7. ورکړل شوی سکیچ بورډ ته پورته کړئ.
  8. په پیل کې وګورئ چې د بورډ LED بند دی.Digilog-ESP32-Super-Mini-Dev-Board-fig-3
  9. Closing the switch will make the onboard LED start blinking at a 2-second interval.
  10. Ensure that the onboard LED is on.f
  11. Gently touch the male side of the hanging wire/jumper with h G-pin of the Mini Board.
  12. Confirm that the onboard LED is blinking at a 2-second interval.
  13. Press the RST (Reset) Button of the Mini Board and repeat the process if needed.

اسناد / سرچینې

ډیجیلاګ ESP32 سوپر مینی دیو بورډ [pdf] لارښوونې
د ESP32 سوپر مینی ډیو بورډ، ESP32، سوپر مینی ډیو بورډ، مینی ډیو بورډ، بورډ

حوالې

یو نظر پریږدئ

ستاسو بریښنالیک پته به خپره نشي. اړین ساحې په نښه شوي *