د EPH کنټرولونه TR1V2-TR2V2 RF مین سویچ
مشخصات
- د بریښنا رسول: 200 - 240VAC 50-60Hz
- د اړیکو درجه: 230 Vac 10(3)A
- محیطي حرارت: 0…45˚C
- اتوماتیک عمل: Type 1. C.
- د وسایلو ټولګي: د دوهم ټولګي وسیله
- د ککړتیا کچه: د ککړتیا درجه 2
- د IP درجه بندي: IP20
- درجه بندي تسلسل Voltage: د حجم په وړاندې مقاومتtage surge 2500V د EN 60730 مطابق
ستاسو TR1 TR2V2 څنګه کار کوي
- Your TR1 TR2V2 is used to send a wireless signal from one location to another when running Cables is difficult, expensive, or otherwise not an option.
- The product comprises two devices: a TR1V2 and a TR2V2. Both devices are pre-paired during manufacturing for user convenience.
- When 230V is applied to the Live in terminal of the TR1V2, the COM and Live out connection closes, which sends voltage from Live out on the TR2V2.
- It is possible to send a wireless signal in one direction or both.
- When a signal is sent from the TR1V2 to the TR2V2, a green light will activate on the TR2V2.
- When the TR2V2 sends a signal to the TR1V2, a green light will activate on the TR1V2.
- Common uses include sending a signal from a programmer to a boiler or hot water cylinder that is in a different location. These are also used to control pump overrun and many other applications.
- It is possible to have more than one set of TR1, TR2V, 2and, where required.
- Please see pages 9-13 for wiring examples
د TR1TR2V2 لپاره د داخلي تارونو ډیاګرام
احتیاط: Installation should only be carried out by a qualified person and by wiring regulations.
Switching Options
د مینې بدلول
- Link L to 3
ټیټ والیومtage بدلول
- Remove the external controls link from the boiler PCB.
- Connect 2 and 3 to these terminals.
پورته کول او نصب کول
- The TRIV2 should be wall-mounted in an area within 30 metres of the TR2V2. Both TRIV2 & TR2V2 must be mounted more than 25cm away from metal objects, as this will affect communication. The TRIV2 & TR2V2 should be installed at least 1 metre from any electronic devices such as radio, TV, microwave, ve, or wireless network adapter. They can be fitted to
- Single-gang recessed back box.
- د سطحې نصب کولو بکسونه
- Directly mounted on a wall.
- Use a Phillips screwdriver to loosen the screws of the backplate on the bottom of the TRIV2 & TR2V2, lift upwards from the bottom, and remove the backplate.
- Screw the backplate to the wall with the screws provided.
- بیکپلیټ د تارونو ډیاګرام سره سم وصل کړئ.
- Mount the TRIV2 & TR2V2 on the backplate, making sure the pins and the backplatcontactsts are making a sound connection. Push the TRIV2 & TR2V2 flush to the surface and tighten the screws of the backplate from the bottom.m
تڼۍ / LED تفصیل
لارښود Press to activate or deactivate the Live out terminal.
نښلول Hold for 3 seconds to initialise the pairing process. The RF light will flash.
بیا تنظیم کړئ Press to reset the T, R1, TR2V2.
یادونه: The connection procedure is not required as both TR1 & TR2V2 are pre-paired
د LED تفصیل
| LED | رنګ | تفصیل |
| په LED کې ژوند وکړئ | سور | هیڅ والی نشتهtage on the Live terminal. |
| شین | حجم شتهtage په ژوندۍ بڼه ټرمینل کې - اوس به د ژوندۍ بڼې ټرمینل فعالولو لپاره د RF سیګنال بل RF مین سویچ ته واستول شي. | |
| RF LED | سپین | سالډ سپین LED دا په ګوته کوي چې ترموسټاټ وصل دی. |
| د RF څراغ به دوه چنده شي کله چې ترموسټاټ منحل شي. د ترموسټاټ جوړه کول چیک کړئ. | ||
| یادونه: د RF څراغ به په موقتي ډول راښکاره شي کله چې سیسټم د مخابراتو لپاره سیګنال لیږل او ترلاسه کوي. | ||
| یادونه: The RF light will blink once every second when in RF pairing by holding Connect. Press the Manual to exit from this state. | ||
| د LED ژوند کول | سور | د بل RF مین سویچ څخه د RF فعالولو سیګنال نه دی ترلاسه شوی. |
| شین | RF activation signal has been received from the other RF Mains Switch. |
To connect the TRI TR2V2
مهرباني وکړئ په یاد ولرئ: When installing TRI TR2V2 RF mains switches, both TRI &TR2V2 are pre-paired. The procedures below are not required.
On TR1V2:
- نیول for 3 seconds until the RF LED flashes white.
On TR2V2:
- نیول د 3 ثانیو لپاره.
- The RF LED will begin to flash, and the Live out LED will appear solid green.
- When connected, all three LEDs will appear solid.
On TR1V2:
- فشار ورکړئ to exit the pairing mode.
- After connecting successfully, the RF LED on both TR1V2 & TR2V2will appear solid.
To disconnect the TRI TR2V2
- نیول for 3 seconds until the RF LED flashes white.
- نیول for 10 seconds until the Live in LED appears solid red.
On TR2V2:
- نیول for 3 seconds until the RF LED flashes white.
- نیول Connect for 10 seconds until the Live in & Live out LED appears solid red.
On TRIV2:
- مطبوعاتي د وتلو لپاره
- The TRI TR2V2 is now disconnected.
ویرنګ Examples
Example One way RF Switch: Programmer to Boiler – Mains Switching
TR1V2
On TR1, when Live in receives 230V from the programmer, TR1 sends a wireless signal to TR2.
TR2V2
On TR2, the COM & Live out contact closes, sending 230V to activate the boiler.
د نصب یادښتونه
- Mains Switching Boiler
- ټیټ-Voltage Switching Boiler
- په TR2V2 کې
- On the boiler PCB
- په TR2V2 کې
- Link L to 3.
- Remove the external controls link.
- Connect terminals 2 & 3 to the external controls terminals on the boiler PCB.
Example 2 Two Two-way RF Switch:
- Programmer to Motorised Valve
- Motorised Valve to Boiler – Mains Switching
T RI v2
- On TRI
When Live in receives 230V from the programmer, TRI sends a wireless signal to TR2. - On TRI
Live out contact closes, sending 230V to activate the boiler.
TR2V2
On TR2, the COM & Live out contact closes, sending 230V to activate the motorised valve. When the valve auxiliary switch engages, it sends 230V to the Live in contact. TR2 then sends a wireless signal to TRI.
د نصب یادښتونه
1. Main Switching Boiler
2. ټیټ-Voltage Switching Boiler
۳. د موټرو والو
- On the TRIV2
- On the boiler PCB
- On the TRIV2
- په TR2V2 کې
- Link L to 3.
- Remove the external controls link.
- Connect terminals 2 & 3 to the external controls terminals on the boiler PCB.
- Link L to 3 to power the Live out terminal to the motorised valve.
Example 3 One way RF Switch:
Pump Overrun – Mains Switching
TR 1 v2
- On TRI, when Live in receives 230V from the boiler, TRI sends a wireless signal to TR2.
TR2V2
On TR2, the COM & Live out contact closes, sending 230V to activate the pump.
د لګولو یادښت
- پمپ کول
- the TR2V2
- Link L to 3 to power the Live out terminal to the pump
Example 4 Two Two-way RF Switch: Pump Overrun
- پروګرامر تر بویلر پورې
- Boiler to Pump – Mains Switching
T RI v2
- On TRI
When Live in receives 230V from the programmer, TRI sends a wireless signal to TR2. - On TRI
Live out contact closes, sending 230V to activate the pump.
TR2V2
- On TR2, the COM & Live out contact closes, sending 230V to activate the boiler. When the boiler turns off, the pump overrun activates, sending 230V to the Live in contact. TR2 then sends a wireless signal to TRI.
د لګولو یادښت
- Mains Switching Boiler
- ټیټ-Voltage Switching Boiler
- پمپ
- په TR2V2 کې
- On the boiler PCB –
- په TR2V2 کې
- On the TRIV2
- Link L to 3.
- Remove the external controls link.
- Connect terminals 2 & 3 to the external controls terminals on the boiler PCB.
- Link L to 3 to power the Live out terminal to the pump.
Example 5 Two Two-way RF Switch: Unvented Cylinder:
- د لوړ حد ترموسټاټ ته پروګرامر
- Motorised Valve to Boiler – Mains Switching
T RI v2
- On TRI
When Live in receives 230V from the programmer, TRI sends a wireless signal to TR2. - On TRI
Live out the contact closes, sending 230V to activate the boiler.
TR2V2
On TR2, the COM & Live out contact closes, sending 230V to the high limit thermostat, powering the brown cable of the motorised valve. When the motorised valve auxiliary switch engages, it sends 230V to the Live in contact. TR2 then sends a wireless signal to TRI.
د نصب یادښتونه
- Mains Switching Boiler
- ټیټ-Voltage Switching Boiler
- لوړ حد ترموسټات
- د موټرو والوز
- On the TRIV2
- On the boiler PCB
- په TR2V2 کې
- Link L to 3.
- Remove the external controls link.
- Connect terminals 2 & 3 to the external controls terminals on the boiler PCB.
- Link L to 3 to power the Live out terminal to the High Limit thermostat.
د EPH کنټرول IE
technical@ephcontrols.com
www.ephcontrols.com/contact-us
+353 21 471 8440
cork, Tl 2 W665
EPH د انګلستان کنټرول
technical@ephcontrols.co.uk
www.ephcontrols.co.uk/
موږ سره اړیکه ونیسئ
+44 1933 322 072
Harrow, HAI IBD
FAQs
Q: Can I install the TR1, TR2V2V2 devices myself?
A: Installation should only be carried out by a qualified person following wiring regulations to ensure safety and proper functionality.
پوښتنه: د اغیزمن اړیکو لپاره د TR1V2 او TR2V2 ترمنځ اعظمي فاصله څومره ده؟
A: The recommended distance is within 30 meters for optimal wireless signal transmission.
اسناد / سرچینې
 |
د EPH کنټرولونه TR1V2-TR2V2 RF مین سویچ [pdf] د لارښوونې لارښود TR1V2، TR2V2، TR1V2-TR2V2 RF مینز سویچ، TR1V2-TR2V2، د RF مینز سویچ، مینز سویچ، سویچ |