اونسمي v1 Samples / Eval Boards
د محصول معلومات
- برانډ: اونسمي
- Product Type: Sampد امر کولو طریقه
- Webسایټ: https://www.onsemi.com/
پیژندنه
- CCE4511 devices can be evaluated by using the CCE4511 Evaluation Board connected to any suitable external MCU.
- The CCE4511 Evaluation Board contains two CCE4511 devices including all necessary periphery to use them for IO-Link communication on 8 channels with any suitable external MCU.
- The CCE4511 Evaluation Board is compliant with the IO-Link Interface and System Specification V1.1.3, and it can be controlled by either of the following methods:
- Via SPI, using the PMOD interface (JP7 or JP8)
- Control each channel directly via UART interface (JP2, JP3, JP5 and JP6).
د سیسټم اړتیاوې
- For evaluation, the following tools are required:
- External MCU (for example, Renesas YCONNECT-IT-RZN2L)
- 24V بریښنا رسول
- 3.3V Power supply for the CCE4511 Evaluation Board and the external MCU
- IDE and coding tool (e.g. Renesas e² Studio)
- The following tools are optional depending on the user setup:
- Connection cable to connect external MCU to PMOD interface (JP7 or JP8), use it if no PMOD interface is available on MCU side.
- Connection cables to connect UART interfaces to external MCU.
Board Hardware Overview
- The CCE4511 Evaluation Board has the following features (for placement of parts and connectors, see Figure 2):
- M12 A-Coded IO-Link connectors (8 channels)
- Optional IO-Link Port Class B power supply for all IO-Link channels
- Two CCE4511 IO-Link Master Transceiver ICs
- Two status LED indicators per channel
- External NMOS gate drivers
- Additional on-board protection circuitry
- د بریښنا LED شاخصونه
- PMOD type 2A (expanded SPI)
- UART interface pin-headers
- +3.3V power select jumper
د بریښنا رسول
- The Evaluation Board needs to be powered by two external power supplies: the main supply voltage VVS (+24V, X9 or X10) and the pad supply voltage VVDDIO (+3.3V, X11).
- Note: Both supply voltages are mandatory for proper functionality!
- X9 is a standard DC Power Jack (Würth Elektronik PN 694106301002) with a center pin diameter of 2mm. The recommended plug inner diameter is 2.1mm, recommended plug outer diameter is 5.5mm.
- It is possible to supply the connected IO-Link devices with a port class B power supply via JP1 and JP4, where:
- JP1 supplies CH1, CH2, CH5, CH6
- JP4 supplies CH3, CH4, CH7, CH8.
- It is possible to power the pad supply voltage VVDDIO (+3.3V) via the connected MCU using the PMOD interface.
- If a jumper is placed at the PMOD position of the power select jumper (JP9), the connected MCU powers the pad supply voltage. If a jumper is placed at the EXT position, the pad supply voltage needs to be sourced externally (see Figure 4).
- Two LEDs (D42 and D43) indicate if the power supplies are available.
ارتباط
- The CCE4511 Evaluation Board contains two CCE4511 IO-Link Master Transceiver ICs, implementing 8 IO-Link Master ports. Each IO-Link Master port uses a standard M12 A-Coded connector to connect an IO-Link Device.
- Table 1 shows the assignment of the channels of each CCE4511 (IC1 and IC2) to the channel names of the Evaluation Board.
- Table 1. Channel Assignment
- Each channel is using an external NMOS (Q1 for CH1) to switch the LP voltage of the channel on or off, and an 0.5Ω resistor (R1 for CH1) to limit the channels maximum current to 500mA utilizing the CCE4511s LPx over-current detection feature.
- Each channel is protected against surge, burst and reverse polarity using two TVS diodes and one Schottky diode, see section 5 for details.
- Two LEDs (D7 and D8 for CH1) with programmable 8-bit pattern can be used to indicate the channels status.
- To connect the CCE4511 Evaluation Board to an MCU, use the PMOD connector (JP7 or JP8) and the UART interface connectors (JP2 and JP3 for IC1, JP5 and JP6 for IC2).
- JP7 and JP8 have the same pin assignment. JP8 allows for easy access to the SPI signals for measurements while the CCE4511 Evaluation Board is connected to any host MCU via JP7.
- It is possible to directly control the channels using the UART interface of each CCE4511, see the CCE4511 Datasheet document for more information about directly controlling the channels.
پیل کول
To start evaluating devices using the CCE4511 Evaluation Board, follow these steps:
- Connect the PMOD interface (JP7 or JP8) to an external MCU.
- Set jumper JP9 to use either the PMOD power supply or an external power supply for 3.3V (pad supply voltage VVDDIO)
- If external 3.3V: connect the external 3.3V power supply (X11)
- Connect the 24V power supply (X10)
- Power on the 3.3V power supply
- Power on the 24V power supply
- Start customer-specific evaluation.
د موادو بل
د امر کولو معلومات
لغت
د بیاکتنې تاریخ
- مهم خبرتیا او اعلامیه
د رینیساس الکترونیکي کارپوریشن او د هغې فرعي شرکتونه ("رینیساس") تخنیکي مشخصات او د اعتبار ډیټا (د ډیټا شیټونو په شمول)، ډیزاین سرچینې (د حوالې په شمول)، د حوالې نور وسایل چمتو کوي WEB وسیلې، د خوندیتوب معلومات، او نورې سرچینې "لکه څنګه چې وي" او د ټولو نیمګړتیاوو سره، او ټول تضمین ردوي، په شمول، پرته له محدودیت څخه، هر ډول تضمین، د تضمین لپاره، یا د دریم نه سرغړونه- د ګوند د فکري ملکیت حقونه.
- These resources are intended for developers who are designing with Renesas products.
- You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements.
- These resources are subject to change without notice. Renesas permits you to use these resources only to develop an application that uses Renesas products.
- Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third-party intellectual property.
- Renesas مسؤلیت ردوي، او تاسو به Renesas او د هغې استازو ته د هرې ادعا، تاوان، لګښتونو، زیانونو، یا مسؤلیتونو په وړاندې چې ستاسو د دې سرچینو کارولو څخه رامینځته کیږي په بشپړه توګه جبران کړئ.
- د رینساس محصولات یوازې د رینساس د پلور شرایطو او شرایطو یا نورو پلي کیدو شرایطو سره سم چمتو شوي چې په لیکلي ډول ورسره موافقه شوي.
- د دې محصولاتو لپاره د هیڅ رینساس سرچینې نه کارول پراخیږي یا بل ډول د پلي کیدو وړ تضمین یا تضمین اعلانونه نه بدلوي.
نور معلومات
- د کارپوریټ مرکزي دفترونه
- TOYOSU FORESIA, 3-2-24 Toyosu,
- کوټو کو، توکیو 135-0061، جاپان
- www.renesas.com
- سوداګریزې نښې
- Renesas and the Renesas logo are trademarks of Renesas.
د اړیکو معلومات
- د محصول، ټیکنالوژۍ، د سند ترټولو تازه نسخه، یا ستاسو د پلور نږدې دفتر په اړه د نورو معلوماتو لپاره، مهرباني وکړئ لیدنه وکړئ www.renesas.com/contact-us/.
FAQ
پوښتنه: ایا زه کولی شم امر وکړم؟amples without creating an account?
A: No, you need to either log in as an existing user or register as a new user to order samples from onsemi.
Q: Are there any costs associated with ordering samples؟
A: Typically, onsemi provides samples for evaluation purposes free of charge. However, shipping costs may apply.
اسناد / سرچینې
 |
اونسمي v1 Samples / Eval Boards [pdf] د مالک لارښود v1 Samples Eval Boards, v1, Samples Eval Boards, Eval Boards |